Valves
We lock our exhaust valves open on our GT4 with some old high temperature 1/4” fuel hose and some hose clamps. Be sure to use a hight temperature rated hose because the exhaust gets HOT! Link to get some fuel hose with clamps https://amzn.to/4e8y5Y9 Download your shop manual from eManualOnline.com in the link below: Cayman […]
Replace PCV Valves Nissan Armada Patrol Titan Infiniti QX80 QX56. How to clean PCV Valves NISSAN Armada. How to service the PCV valve Nissan Infiniti Amazon – Nissan OEM PCV Valve – (paid link) https://amzn.to/4m7PnrT Amazon – NonOEM PCV Valve – (paid link) https://amzn.to/3VfqNKY Amazon – 23mm Socket – (paid link) https://amzn.to/3JTPRET Amazon – Long […]
Replace PCV Valves Nissan Armada Patrol Titan Infiniti QX80 QX56. How to clean PCV Valves NISSAN Armada. How to service the PCV valve Nissan Infiniti Amazon – Nissan OEM PCV Valve – (paid link) https://amzn.to/4m7PnrT Amazon – NonOEM PCV Valve – (paid link) https://amzn.to/3VfqNKY Amazon – 23mm Socket – (paid link) https://amzn.to/3JTPRET Amazon – Long […]
Hyundai & KIA GDI Engines deliver increased power, performance and gas mileage. GDI or gas direct injection engines, they’re great engines but then need a bit more periodic maintenance. If you drive one of these vehicles, this is important. Because of their design, these engines need treatment with CRC GDI IVD Intake Valve & Turbo […]
Replaced the old steel reed valves on a 2013 Mercury 250 ProXs outboard with a new set of Chris Carson carbon fiber reed valves. Please visit HawkeyeMarine.net for parts @ http://www.hawkeyemarine.net. Parts and supplies for your boat. Thanks for watching and subscribing. #boatmaintenance #boatservice #boating #ChrisCarson #boating Please subscribe to the channel: http://www.youtube.com/@hawkeyemarine?sub_confirmation=1 Most recent […]
Cleaning intake valves on direct injection engines is a common maintenance task due to the buildup of carbon deposits. Unlike port fuel injection engines, where fuel washes over the intake valves, direct injection engines inject fuel directly into the combustion chamber, bypassing the intake valves. This can lead to carbon deposits accumulating on the intake […]
In this video, you will be taught how to increase the car’s acceleration and reduce the car’s consumption by adjusting the car valve
PORSCHE ENGINE REBUILD STEP BY STEP: How to Clean and Refinish Valves Today we are cleaning the valves before lapping them, it’s a easy process that only takes some time to clean each valve. BUY RED CLEANING PADS HERE: https://amzn.to/3roKMLu I have a 1967 Porsche 912 coupe, with a 1976 Porsche 912e engine installed. The […]
In this video I explain all solenoid valves on the new generation of front wheel drive automatic transmission on Hyundai and KIA (8 speed automatic transmission) with these codes: A8LF1 and A8MF1 I explain the solenoid valves location, their types, how to check them in the scan tool and how to check the solenoid valves […]
Now that we have the RH cylinder head off this 2014 Subaru Forester, let’s replace some EXHAUST VALVES! One out of 4 valves is obviously severely burned, but what do the other 3 look like? What is the ROOT CAUSE behind this weird failure? Lisle 36050 Valve Keeper Remover and Installer Kit: https://www.amazon.com/dp/B0012S61IO?tag=onamzpineholl-20&linkCode=ssc&creativeASIN=B0012S61IO&asc_item-id=amzn1.ideas.2N7WCA81DLG3L Enjoy! Ivan
Brian Eslick from How to Automotive http://www.howtoautomotive.com/ takes you step-by-step through the process of installing Torque Solution’s Billet Tgv Delete Kit for 2015-2018 Subaru WRX vehicles. By deleting the tumble generator valves and installing Torque Solution Billet Tgv Delete Kit you will gain horsepower and torque. (Subaru WRX Modifications) #HowtoAutomotive #AutomotiveRepair #SubaruWRX Affiliate link mentioned […]
This video demonstrate the removal and replacement of the Intake Valve Timing Control Solenoid Valve. I am demonstrating on a 2005 Nissan Xterra but this could be used for any Nissan with the matching motor such as the Frontier, X-Trail, Navara, and some Armadas. If you are getting codes P1111 or P1136 this could be […]
In this video we do a brief introduction to the Land Rover / Range Rover Tyre Pressure Monitoring System ( TPMS ) and look how to replace a leaking valve stem. The valve stem can be separated from the actual TPMS sensor so you can replace the valve seals without needing to replace the actual […]
This video will show you how to properly install valves, valve springs and valve keepers on your 3.7 or 4.7 Chrysler engine. Jeep Grand Cherokee, Jeep Liberty, Dodge Durango, Dodge Truck 1500, Dodge Dakota -~-~~-~~~-~~-~- Please watch: “Flipping cars, $800 2000 Toyota Rav4, before walkaroud” https://www.youtube.com/watch?v=orV8UiGnTd0 -~-~~-~~~-~~-~-
In this Subaru DIY / How-To video I walk through the details of Subaru Timing Belts, Accessory Pulleys, and Hydraulic Tensioners. I discuss how they are designed, how they function, and how to service them the RIGHT way – with great close-up shots – to help YOU apply these TIPS to your Subaru! ———– 🔹 […]
T-Shirts: http://www.zrokids.com/shop/ Facebook: https://www.facebook.com/zrokids/ Instagram: https://www.instagram.com/zro_kids/ Twitter: https://twitter.com/DanielHurlbert Subscribe: https://www.youtube.com/danielhurlbert My new exhaust valves already broke. Time to do a little DIY fix.
If you need to remove a valve from a cylinder head either to replace the valve or replace the valve seals, this video will help you do that. You can also do …
TheCousinDan shows you how to replace your valve seals and grind the valves into a proper seat in your cylinder head.
This is a video to show you how simple it is to replace damaged SCV valves on a Toyota D4D engine. Damaged valves can cause loss of power from the engine, wh…
Will a blow off valve make your car faster? Can you install one on a non-turbo car? How do they work? All these questions answered and a whole lot more thank…
A short video by Vern Tardel showing how to install and adjust new valves in a Ford flathead V-8.
To do this you will need a valve spring compressor, some lapping compound and the suction cup stick used to rotate the valves. I also show you what to look f…
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
')){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
){kind=link}
Kent shows you how he safely and efficiently remove the leveling valves from under a W109 Chassis. Seems simple enough, but this job can be especially challe…
){kind=link}