This video demonstrate the removal and replacement of the Intake Valve Timing Control Solenoid Valve. I am demonstrating on a 2005 Nissan Xterra but this could be used for any Nissan with the matching motor such as the Frontier, X-Trail, Navara, and some Armadas.
If you are getting codes P1111 or P1136 this could be what’s causing the problems. The Nissan Product number for the gaskets is 23797-ZA000.
Here is the amazon link for it: https://amzn.to/2rG4Ve1
The backstory: http://rtcg.tv/2018/05/14/vvt-soleniods-and-regretting-past-decisions/
Check out the Official RTCG website! http://rtcg.tv
Support the channel and get a cool t-shirt: https://represent.com/store/ry-the-car-guy
The Hunter by Audionautix is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/)
Artist: http://audionautix.com/
***As an Amazon Associate I earn from qualifying purchases by use of affiliate links.
#howto #diy #auto
Thanks so much for making this video. I don't barely know anything about cars but I wasn't about to spend the money to let the shop fix it. This video was very clear to understand and my car is running like new! Thanks to all the YouTube mechanics!
Do you need to reprogram the engine computer. Or the timing? Just curious.
How did you know to use 8 ft pounds of torque, mine keep leaking and that much torque doesn't seem to be enough and I can't find anything anywhere on the torque specs
Hi, Nissan diagnosed my 2010 Murano with Bank 1 Selonoid valve error. Is it this same valve?
Could these valves or solenoids cause a knocking/tapping sound on my 2013 Frontier V6 (128K miles)? Thanks!
Done it while doing the plugs and valve cover gasket, had to remove it anyway so I put 2 new ones, solenoids and gaskets.
Is the one on passenger side bank 1?
I really wanna make sure I order the right part.
06 Nissan altima 3.5 where is the intake valve timing located.
Hello, was this one the exhaust or intake vvt? Thanks for your time.
Thanks for the great videos! Somehow I set my torque wrench to 8lbs and it snapped the bolts! Not sure what happened.. maybe torque wrench bad, bolts old, or oil on bolts. But luckily the bolt snapped and was still protruding outside the screw-hole to unscrew it.
Very helpful video … And nice job !! Just one question this is the same job for P0021 code ?
Hi ry I have a 05 Nissan xterra with code p1754 coast clutch solenoid circuit according to auto zone any recommendations?
I replace the timing solenoid on my 2003 Nissan Altima , and the check engine light came on again ,,little help please …
Why didn't you remove the solonoid from the housing and clean it & the screens too?. It's only 1 bolt
Ry, had a P0021 error code pop up after a rough start up. The dealership says my timing chain is worn and needs replacing.I’ve always kept up with my 2011 Xterra maintenance, so I don’t see how a car with less than 100k would need a new timing chain. Do you think the VVT solenoid would trigger a misfire code and cause the idle to seem rough or even weak?
Any body knows ecu pin terminal for signal to driver side is it pin 10 want to check for continuouty on this vvt selenoid having issue with it replaced it many times and no sucess
What about p0014?
I am getting 0011 and 0021. this isn't the same?
Do you know where the intake vvt solenoid is on a nissan micra?
Ok friend you are expert on cars i got xterra 2005
I got headache of code p1136
Flushed engine 2ith fuel as you told us before to soak it overnight and drain it Did It 6 times and engine run great except for p1136 code
Its vvt selenoid ive changed it 3 or 4 times
Changed oil and filter
Cleaned cam sensor still after clearing its coming back on 3 Rd start up
Checked harness of vvt 2 wires one give battery voltage and one is ground its ok no voltage
Next step will be replacing cam sensor
Any suggestion will be appreciated
Also i dont know will bigger battery 900 cca 90 amp adversly affect the car so instead of 700 cca 70 amp?