Get a new axle or other parts here: http://amzn.to/2DG2Tzo Tall Shop Press: http://amzn.to/2DqVvug Car Guy Supply Guide: https://www.amazon.com/shop/carguysupply How to replace a Toyota Tundra rear axle shaft, bearing, and seals without a shop press. This truck slid into a boulder and bent the axle shaft. Luckily there was no damage to the axle housing. This […]
This is a step-by-step installation video for the first generation Toyota Rav4 (3SFE engine) — timing belt, water pump, crankshaft seal, camshaft seal, oil pump housing gasket, oil pump shaft seal, tensioner pulley and idler pulley. The crankshaft bolt was a bear on this one! But I’ll show a way to remove it. Check the […]
Tearing into the forks of a motorcycle can seem like too big of a job for a lot of people. But learning how to replace them yourself will save you tons of time and money over the course of owning your bike. In this video, Justin shows the proper steps to replacing the fork seals […]
In which we remove the door glass and repair the inner and outer door glass seals on the Lotus Elan M100. We show how to get the glass out without severing your fingers; fit and adjust the sliders so the window opens smoothly without rattling; put it back in and adjust it so it doesn’t […]
Door seal installation: 30 to 45 minutes. In this video I show how I installed the door seals on a Volvo 850. It should be the same for other Volvo vehicles. To remove the seal, you need to push the pin through the clip, into the door.
M54/M52 TU vanos seal replacement as well as M54 rattle kit DIY. I did this procedure on my 2001 BMW E46 330i wagon Links to parts: M54/M52TU Vanos Kit: https://click.linksynergy.com/link?id=BZfgVZ7JGM8&offerid=580643.14009144654&type=2&murl=https%3A%2F%2Fwww.ecstuning.com%2Fb-ecs-parts%2Fecs-m5x-dual-vanos-rebuild-kit%2F012017ecs%7Edk%2F http://www.beisansystems.com/ Shop Appointment Requests/Questions/Merchandise: http://www.shoplifetv.com Support my channel by becoming a member using this link: https://www.youtube.com/channel/UC5jnm5CEnLSEmoQ-ktgAj6g/join Instagram: @ShopLifeTV https://www.instagram.com/shoplifetv/ Business Inquires (only for youtube): You […]
Buy Now! New Wheel Bearing & Seal Kit from 1AAuto.com http://1aau.to/ia/1ASHS01077 🔧 List of tools used: • Flat Blade Screwdriver • Pry Bar https://www.1aauto.com/*/i/1AXAA00020?utm_source=YouTube&utm_medium=description&utm_campaign=videodesc&utm_term=FvzDuXDzo_A • 10mm Wrench • 15mm Wrench https://www.1aauto.com/*/i/1AXAA00010?utm_source=YouTube&utm_medium=description&utm_campaign=videodesc&utm_term=FvzDuXDzo_A • 10mm Socket • 15mm Socket • 21mm Socket • Brake Caliper Compressor Tool. Single Piston. Screw Style. https://www.1aauto.com/*/i/1AXAA00012?utm_source=YouTube&utm_medium=description&utm_campaign=videodesc&utm_term=FvzDuXDzo_A • 1/2 Inch Breaker Bar […]
Had the transmission dropped to replace the Torque Converter Seal, Rear Main Seal, Axle Seals, etc… This is not a DYI video, just documenting the process & upkeep on the car. Thanks for watching! #500000miles #transmissionremoval #tsxtravels #acura #acuratsx
DIY Valve stem seals replacement on a BMW N42/N46 engine. Engine suddenly started consuming a lot of oil (6 dcl/1000 km). I had some substantial oil leaks, so I first had to replace: – oil pan gasket, – valve cover gasket, – Valvetronic motor gasket – Valvetronic sensor connector flange, – vaccum pump o-rings, – […]
This is on a ford 9 inch , but can be appled to many different rear ends. Jeeps have the same procedures as well. I cover how to remove a pressed in axle bearing, how to remove a bearing race from an axle tube. how to use a slap slide hammer. how to press in […]
This is how I do valve seals on a Chevrolet head.
In this video I show you the simple steps on how to change out your drive axles,transmission seals & replace the transmission fluid to the proper level. The Vehicle in this video was a 96 Honda Accord Manual Transmission with a F22B1 Vtec engine. This repair works on the following: Honda Accord,Integra,Honda Civic SI 99-00 […]
Front Main Seal, Timing belt, Oil Pump Seal, Camshaft Seal, DIstributor Seal, Waterpump
How to change valve stem seals on most overhead cam heads. This specific head is from a VW Passat with the 1.8 liter turbocharged engine. The concept carries to most overhead cam style engines. Things you may want to buy for the job on Amazon Valve spring compressor: http://amzn.to/2ryNZH0 Magnet: http://amzn.to/2rSZARL Pick set: http://amzn.to/2sBKq16 Grease: […]
In this Subaru DIY / How-to video I walk YOU through the design and install of camshaft seals and camshaft plugs. I also share my $2 Tool Hack (available at any hardware store) to quickly and easily install the front seals or the rear plugs! I walk through each step of the installation process – […]
– This is a DIY for removing and replacing your valve stem seals, valve springs, or the retainers and keepers utilizing the HPT Autosport valve spring compressor tool. The tool is sold for $79.99 from hptautosport.com. The tool will work on the B18A, B18B, B20B, and B20Z non vtec heads. It will not work on […]
Turbo drain leak: 30 to 60 minutes ($10 / $110 / $160) In this video I replaced the seals on the turbo drain tube on a Volvo S70 GLT. This process is the same on several Volvo turbocharged cars, 850, XC70, etc.
I DO COMPLETE VALVE STEM SEALS FOR $3000. DEALER PRICE $8-12K EMAIL ME @: knightsmastertech@gmail.com (Leave your contact info) After noticing white smoke w/a bluish tint coming …
Dr. Dirt’s Step-By-Step Fork Seal Swap. Leaky fork seals are, for lack of a better description, a royal pain in the neck. The most common ailment to plague front suspension, a leaky fork…
Thought I would make this video since these things are a ***** to take out. And for the visual learners like myself. Unless you have the right tools. The tool I’m using is a door clip removal…
Thought I would make this video since these things are a ***** to take out. And for the visual learners like myself. Unless you have the right tools. The tool I’m using is a door clip removal…
Replacing Rear Wheel Bearings and Seals on a Ford 8.8 28 Spline axle with an open differential. Note: The Ford 8.8 28 spline differential uses many of the sa…
This eight part video series covers a tear down of the front of the 3.0L engine found in many Chrysler products. The vehicle shown is a 2000 Dodge Caravan wi…
This eight part video series covers a tear down of the front of the 3.0L engine found in many Chrysler products. The vehicle shown is a 2000 Dodge Caravan with a serious oil leak.The front…
TheCousinDan shows you how to replace your valve seals and grind the valves into a proper seat in your cylinder head.
This is a quick video on what to use and how to remove and reinstall valve stem seals without removing the cylinder head on a GSR LS Vtec.
This is a quick video on what to use and how to remove and reinstall valve stem seals without removing the cylinder head on a GSR LS Vtec.
This is a quick video on what to use and how to remove and reinstall valve stem seals without removing the cylinder head on a GSR LS Vtec.
Procedures to reseal Ford FS10, Halla HS18/20 used on Ford, Hyundai, Kia, and Dodge Ram vehicles. Parts used include: SK-731N/MK (master kit includes plastic…
This eight part video series covers a tear down of the front of the 3.0L engine found in many Chrysler products. The vehicle shown is a 2000 Dodge Caravan wi…
This eight part video series covers a tear down of the front of the 3.0L engine found in many Chrysler products. The vehicle shown is a 2000 Dodge Caravan wi…
This eight part video series covers a tear down of the front of the 3.0L engine found in many Chrysler products. The vehicle shown is a 2000 Dodge Caravan wi…
Some outboard motor jobs are more difficult than others however having the correct information is the key regardless of how big the job is. Performance Produ…