I too have had the 2004 KIA Sorrento crank shaft bolt break twice. Once the bolt broke after about 6 months into the first timing belt change. I took it to t…
I too have had the 2004 KIA Sorrento crank shaft bolt break twice. Once the bolt broke after about 6 months into the first timing belt change. I took it to t…
If you want detailed written instructions check out this blog post http://vats.likeabigdog.com/
Finally all done. Got frustrated and ground down the bolts a little and it fit in with little trouble.started it up and seems fine, though it sounds horrible…
Finally all done. Got frustrated and ground down the bolts a little and it fit in with little trouble.started it up and seems fine, though it sounds horrible…
How to use the Chrysler dampener puller (OEM part 27139) to remove a pulley from the Chrysler 2.7 engine. See complete timing chain replacement guide at http…
This case study will be useful in troubleshooting no crank problems on any car. The starting system is the main focus of this video. Visit my website, www.sc…
Comments from Paul Diguer: I did a quick video on how to remove the CPS. I forgot to mention in the video their is a steel plate on the transmission that wil…
This video will show you the location of the crank sensor for a pacifica 2004.
This video will show you the location of the crank sensor for a pacifica 2004.
This video will show you the location of the crank sensor for a pacifica 2004.
This video will show you the location of the crank sensor for a pacifica 2004.
Those relay switches are available from Amazon HERE→http://www.amazon.com/gp/product/B006ZW195C/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&camp=1789&creative=9325&cr…
Those relay switches are available from Amazon HERE→http://www.amazon.com/gp/product/B006ZW195C/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&camp=1789&creative=9325&cr…
This video will show you the location of the crank sensor for a pacifica 2004.
When & Where Needed: **** Raise & support the vehicle safely according to Manufacturer Jacking & Supporting Positions!!! **** Rate, Comment, Share, Subscribe…
East steps to replace crank position sensor.
How to Fix No Crank No Start Lincoln Navigator in Easy Steps Year Model 2004 Please visit my website: http://easysteps.jimdo.com/ Thank You for watching, Enjoy, and Please don’t forget to:…
This video shows you how to lift your truck equipped with torsion bars. This tbar lift is done on a 2001 Mazda B3000 / Ford Ranger. You will need an alignmen…
This video shows you how to lift your truck equipped with torsion bars. This tbar lift is done on a 2001 Mazda B3000 / Ford Ranger. You will need an alignmen…
How to remove the crank pulley bolt on a 2004 Acura TL to change the timing belt. Please excuse my calling the ratchet a socket. Also pardon my calling an im…
IN THIS TUTORIAL WE SHOW YOU HOW TO CHANGE THE CRANK SENSOR FOR THE MERCEDES BENZ.
If you have a vehicle with the GM 3800 Engine which stalls randomly and may not always restart, then you likely have a bad crankshaft position sensor. If you…
My jeep would die ramdomly,wether im on the interstate,the trails,the streets etc,then it would start back up after about 10-25 min,well this isnt good when …
IN THIS TUTORIAL WE SHOW YOU HOW TO CHANGE THE CRANK SENSOR FOR THE MERCEDES BENZ.
www.EdgeMotors.com PLEASE LIKE AND SHARE THIS VIDEO!!! In this video we show you how to replace a PCV valve on a 2.0T FSI motor of VW and Audi. This part could cause allot of issues like vacuum…
Visit me at http://www.ericthecarguy.com/ Whenever you have a no start condition when attempting to start your vehicle it’s important to make the distinction…
No need for special tool — heat and slide the sprocket in place. More details at http://iknowoleg.com/auto/stratus/timing/timing-chain-description-page1.aspx.
http://www.1aauto.com 1A Auto shows you how to install, replace or remove the window crank handle on your Ford Ranger years 95, 96, 97, 98, 99, 00, 01, 02, 0…
An 04 Cadillac with a no crank no start condition and no communication on either the CAN or serial data lines.. How ever if the starter relay is by passed it…
This is where the inspection hole is for hte brank reference on a Kia 4 cylinder. It’s behind the Catalytic convertor. The Cat has to be removed. You will be…
mercury 90 hp tear down, diy, outboard motor rebuild, got stuck on the last screw on the power head, probably need to get a engine lift to hoist the power he…