great video very very informative i love it how you explain everthing. i have 120 hp OD 1996 and reverse gear dont work, what do you think what should i check in lower unit, thats where problem is, linkage cable is where it needs to be. It rattles like crazy when i shift to reverse? thanks (bayliner 1700 ls)
thanks. does this motor leak oil from the engine if the lower is removed off the engine? I just did this replacement today and trimmed the motor all the way up without the lower in it and it started to leak oil. A lot of it.
Thank You for this Video. I did it Myself last night for the first time. I was a little worried at first because after i took off the 5 bolts of my 70hp Merc i couldn’t pull the transfer case off. I was worried perhaps there was a bolt i had missed. Well i didn’t miss any, all it needed was a couple of hits from my mallet and i used a screwdriver to wedge it apart. OMG was the impeller chewed up. Pisses me off i was at mechanic few weeks ago and they said the cooling system was fine.
I did all that and everything came apart fine EXECPT the impeller wont come off the drive shaft! How do I fix that? it will move side to side and upand down slightly but ut WONT come off!!! and I am stuck!
Thanks marynbeau. I have an 80 Hos Merc that didnt have water comin from the tell-tale, an was wonderin how to change the impeller, you saved me some hard earned, so thank you very much for the helpfull clip. She’s up an runnin again and i have fish in the freezer.
Big Grin.
Great Video, WAY More Informative than any other, You mentioned the little things a newbie would not know to do, like rotate shaft clockwise when sliding upper housing over impeller, Great video!
Great Video, WAY More Informative than any other, You mentioned the little things a newbie would not know to do, like rotate shaft clockwise when sliding upper housing over impeller, Great video!
wow, thank u sir… thank was great ! , i watched this then i went and did mine,
mine seemed ok until i pulled it out, and had muitiple cracks and some of the fan blades were soft wich is a sign on going bad soon… Now that i have a new one, OMFG the stream of water that comes out is enough to put out a fire, well a small fire..lol…thanks again ….cheer’s
Great video. One thing though: I read that you are supposed to renew the silicone gasket material at the rear of the pump (actually on the cross member behind the pump) to keep exhaust gasses from entering the pump area.
Sir
Great Video
This spring I plan on doing an impeller replacement on my Johnson 60 hp 2 stroke 2 cylinder
you made it look easy
you did a good job with the video
Thanks for sharing
JT
Thanks for sharing. I’m going to try and replace the water pump on my 2001 115 Optimax. All 3 of the Marine dealers in my areas have poor reviews for service and customer relations, so I figure I can do it better than they can!
Hello! I do have a question ( i may have missed the answer in the comments, but here goes. ) Is this a mercury ‘tower of power’ ? the inline 6cyl? I have a mid-80s that needs lots of service – runs, but hasn’t been touched in a long time .
Another fine video. Thank you. You are saving money for lots of folks by sharing your knowledge. Another topic that would be good is changing lower unit oil. I hear it is relatively simple but I’d like to see it done once before I try it. Thanks again for a great how-too video.
Thanks bro, changing waterpump in a 67 Merc 1100ss and was having problems getting the key set. Found this vid and did like you and got the key problem solved. Finished the waterpum and fired up the Merc Tower of Power and it pumps water just fine. Thanks again.
it’s the exact same process, just take your time, and you will do fine. it really is a simple thing to do by yourself. and thanks for watching the video.
great video very very informative i love it how you explain everthing. i have 120 hp OD 1996 and reverse gear dont work, what do you think what should i check in lower unit, thats where problem is, linkage cable is where it needs to be. It rattles like crazy when i shift to reverse? thanks (bayliner 1700 ls)
Great video I’m doing this for sure!!!
Man I was about to take mine to the shop I’m doing that this weekend now good video
thanks. does this motor leak oil from the engine if the lower is removed off the engine? I just did this replacement today and trimmed the motor all the way up without the lower in it and it started to leak oil. A lot of it.
thanks, Les I’m glad you watched and liked it. hope the video was a help to you.
I have got one smart brother in-law: good job Bo
i gotta do this on my 90 mercury only thing is mine is on of them old two ton inline 6 motors i hate to do it but imma have to
Thank You for this Video. I did it Myself last night for the first time. I was a little worried at first because after i took off the 5 bolts of my 70hp Merc i couldn’t pull the transfer case off. I was worried perhaps there was a bolt i had missed. Well i didn’t miss any, all it needed was a couple of hits from my mallet and i used a screwdriver to wedge it apart. OMG was the impeller chewed up. Pisses me off i was at mechanic few weeks ago and they said the cooling system was fine.
Great video! This worked fine for my 2006 60 hp Mercury Bigfoot. Very few differences. Thanks for posting. Never realized how easy it was : )
What is the little rubber hose that attached to a square fitting that goes right above the lower unit and goes into the front of the motor?
I did all that and everything came apart fine EXECPT the impeller wont come off the drive shaft! How do I fix that? it will move side to side and upand down slightly but ut WONT come off!!! and I am stuck!
Thanks marynbeau. I have an 80 Hos Merc that didnt have water comin from the tell-tale, an was wonderin how to change the impeller, you saved me some hard earned, so thank you very much for the helpfull clip. She’s up an runnin again and i have fish in the freezer.
Big Grin.
Great Video, WAY More Informative than any other, You mentioned the little things a newbie would not know to do, like rotate shaft clockwise when sliding upper housing over impeller, Great video!
Great Video, WAY More Informative than any other, You mentioned the little things a newbie would not know to do, like rotate shaft clockwise when sliding upper housing over impeller, Great video!
wow, thank u sir… thank was great ! , i watched this then i went and did mine,
mine seemed ok until i pulled it out, and had muitiple cracks and some of the fan blades were soft wich is a sign on going bad soon… Now that i have a new one, OMFG the stream of water that comes out is enough to put out a fire, well a small fire..lol…thanks again ….cheer’s
Wendy
Thanks for your great video once again….
very cool, I was scared to do it until watching this video, thanks Tc
I appreciate the very fine and instructional video. Keep up the great work.
Great video. One thing though: I read that you are supposed to renew the silicone gasket material at the rear of the pump (actually on the cross member behind the pump) to keep exhaust gasses from entering the pump area.
great video. could u tell me what u used to hold the lower unit perfectly strait on the floor? thanks.
keep em coming !
Thank you so much, I just finished replacing the water pump on my Mercury 90 HP! You made it very easy! Thanks again, Phil
Sir
Great Video
This spring I plan on doing an impeller replacement on my Johnson 60 hp 2 stroke 2 cylinder
you made it look easy
you did a good job with the video
Thanks for sharing
JT
Very nicely done. Straight forward. Appreciate the time you spent to share with the rest of us willing to swing a wrench and save a little money.
Very nice video. Thanks for taking the time to make and post it.
it’s the same process. just take your time and you will do fine.
will this be the same or close to change waterpump on a 25hp?
Thank You so much sir… Your video truly helps us so much. AAA+++
Thanks for sharing. I’m going to try and replace the water pump on my 2001 115 Optimax. All 3 of the Marine dealers in my areas have poor reviews for service and customer relations, so I figure I can do it better than they can!
How about a Video on how to tune up an outboard?
Hi – great vid. this is what confidence is made of – everything i need to know.
Hello! I do have a question ( i may have missed the answer in the comments, but here goes. ) Is this a mercury ‘tower of power’ ? the inline 6cyl? I have a mid-80s that needs lots of service – runs, but hasn’t been touched in a long time .
Thanks,
Joe
thanks for the comment, and I’m glad you liked it.
Another fine video. Thank you. You are saving money for lots of folks by sharing your knowledge. Another topic that would be good is changing lower unit oil. I hear it is relatively simple but I’d like to see it done once before I try it. Thanks again for a great how-too video.
Your help is much appreciated .Thank you for posting.
thanks for watching the video, I’m glad it helped. thats what it’s all about.
Thanks bro, changing waterpump in a 67 Merc 1100ss and was having problems getting the key set. Found this vid and did like you and got the key problem solved. Finished the waterpum and fired up the Merc Tower of Power and it pumps water just fine. Thanks again.
it’s the same, do it yourself and save the big repair bill. and thanks for watching the video.
Is this the same for a 1981 Mercury 115?
thank you 100% my friend ..just took my time and it all worked out fine..good teacher you are..thanx…
it’s the exact same process, just take your time, and you will do fine. it really is a simple thing to do by yourself. and thanks for watching the video.