Buy Now!
New Fuel Tank Pressure Sensor from 1AAuto.com http://1aau.to/ia/1AEFF00018
In this video, 1A Auto shows you how to repair, install, fix, change or replace a broken, worn out, or damaged fuel tank pressure sensor. This video is applicable to the 00, 01, 02, 03, 04, 05, 06, Chevy Suburban, GMC Yukon XL, or Cadillac Escalade ESV.
🔧 List of tools used:
• Flat Blade Screwdriver http://1aau.to/oQQ/1AXAA00013
• Pry Bar http://1aau.to/oeh/1AXAA00020
• 15mm Socket http://1aau.to/oHX/1AXAA00015
• 8mm Socket http://1aau.to/oC5/1AXAA00017
• Ratchet http://1aau.to/oRC/1AXAA00016
• Socket Extensions http://1aau.to/oHX/1AXAA00015
• Floor Jack http://1aau.to/okZ/1AXAA00068
• Jack Stands http://1aau.to/ok4/1AXAA00065
For More Info visit us at http://1aau.to/h/av2/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Visit-1AAuto
√ Do it Yourself
√ Save Money
Very good edit job on this video. Trust me this job is not as easy as this guy made it look. Take my advice … go ahead and pay the $400 and take it to a mechanic and be done with it. Save yourself the headache.
I've got a broken wire on 03 Tahoe can you tell me or not if the wiring connector from the evap solenoid vapor canister thats behind the tank connects in with the tank vapor sensor? I can't find where that connector leads to as it leads to the top of the tank,i want to replace the Broken wire its about a foot and half long.
The nipple broke off and unable to get it out, can I drive my vehicle after installing the new pressure sensor
Would this be the cause of gas spit out in a 08 tahoe i already replaced evap canister while putting gas
How much of a pain was that?? Will be doing it on my Chevy 3500 shuttle bus and won’t be able to put it on a lift like that.
Will this solve the gas tank building pressure?
I got a Question? I have a 2000 Chevy Suburban 1500 4×4. It hesitates, stalls and have loss of power after start up and And I have had it checked for codes, no codes have came up. So I have changed spark plugs,wires, fuel pump,fuel filter,charcoal canister checked for cracks in hoses and vacuum car cracks at all. Even changed the throttle body and sensors, still same problem. Answers or Ideas anybody?
Is this the same for a 2004 chevy astro van? Please say it's a lot easier or less harder!!!
Remove battery cable for this or doesn’t matter?
Is this the same as the 2003 chevy avalanche? Does your car has engine light on as well?
My trucks smoking does anyone know if that’s the problem
Does this apply to a chevy avalanche 07?? Because I was sent here when u put it in
I loosened strap bolts, they began to strip, then the whole steel around the nut part disintegrated. As in the steel frame perch is literally falling apart. Now What, can a guy replace the frame perch where the straps bolt, completely?
Anyone else tired of not knowing how much gas is in their truck? Lol
07 TB, reading code p0452 E Vap emissions persuade sensor/switch low input would this be the same process??
I had 3 codes related to this problem with new fuel pump installed .
Thanks 1A Auto for the video! Unfortunately most people do not have a Lift in their garage. Or even a garage. So, for most of us lift-less folks, dropping the tank will be a bit more of a challenge. Taking out the spare tire will open up the field of view and work area. Just make sure to jack stand your car to add security/stability.
How do I get the hole into the top for the pressure sensor? Didnt come with a pre made hole
power tools. and give the guy his fix hands are shaking like crazy