If you’re having trouble with the vacuum operated petcock on your Suzuki Vinson or Eiger check out this how to on how to fix the issue and get your 4 wheeler running like new!
Fuel Petcock – https://amzn.to/2OUeOkH
Carburetor w/o Vacuum line (Cannot be used with stock petcock) – https://amzn.to/35Eq8HE
Thank you guys for checking out these videos! As always I hope this video has helped you save some money and get the job done right with your own hands! To make the job even easier, here is a list of tools I use and love that will never let you down! Be sure to subscribe and I’ll see you in the next one!
Milwaukee 3/8 impact – https://amzn.to/2JfJwBF
Milwaukee 3/8 ratchet – https://amzn.to/2LFX3Er
Milwaukee 1/2 impact – https://amzn.to/2L2YMUJ
Torque Wrench 1/4 – https://amzn.to/2XOCdsT
Torque Wrench 3/8 – https://amzn.to/2JequvB
Torque Wrench 1/2 – https://amzn.to/2LENfKW
Channel Locks – https://amzn.to/2xAa5el
BFH – https://amzn.to/2RYlJJ6
Socket Holders – https://amzn.to/2Lb5Kar
Grateful for this. I have the new one in hand ready to install.
You might want to mention that when the Suzuki petcock fails you end up with fuel in the crankcase and an oil & filter change is necessary. I had 1/2 gallon pour out when I removed the oil dipstick.
should the atv should run res or on?
Great video!
Bud, before you crank it after a repair as that, loosen the float bowl drain screw and allow a few c.c. of fuel to run out or into a container. It will fire up instantly.
RESERVE, not reservoir. Hope that helps. Good video.
In the future be sure to use a ETHANOL fuel conditioner or ETHANOL free fuel. It's worth the extra money in the long run, I guarantee it, good luck.
Is the carb that you linked in the description the correct one you put back on the atv? You say it’s set up not for the stock petcock. So can you explain what the other hose/lines are on the carb you linked in your description?
I've got the Quadmaster 500 made just before yours, I thought it was the petcock too, What I found out what it was is there's a filter on the needle seat of the carb remove the seat by taking off the screw holding it in on the bottom is a yellow filter with a E clip remove the clip throw it in the bush the machine problem is solved instantly runs like new, Mine left me in the bush I. Took it back the machanic couldn't find the problem, We'll I found it or walk home it never done it again.
Bro I'm so glad I seen this video, thank very much for the info. Going to order mine stuff now to get mine going asap.
I replaced fuel valve and carb with the ones you mentioned . I can’t seem to adjust the carb my four wheeler Boggs down and shuts off when I put it into drive. Would you happen to know what may be going on with it?
I just bought a used Suzuki Eiger that won't run off idle. The fuel petcock is this stupid vacuum operated mess. This video clearly and cleanly shows exactly how to fix it. THANK YOU!
I have an 03 Eiger that sat with a 1/2 tank of gas for about a year and a half. Draid the fuel (turpentine smell). Fresh fuel. Idles great but the minute you touch the idle it stalls. I'm sure it's the carb but I'm going to do
Does the little black plastic piece where the fuel goes in the carburetor screw out ? My Fuel is blocked right there , can't even blow air through it .
Sounds exactly like the problem I am having with my Suzuki Vinson 500. Thanks for the info!
Where the spark plug at
Yamaha raptor 660.
Did you get the same carburetor with the vacuum line and where did you find it?
I am working on this exact wheeler and that was the last thing that I was gonna replace! I'm glad I found this video. I have already been through the whole carb.