Replacing Saturn (CPS) Crankshaft Position Sensor,s-series.
Replacing(CPS) Crankshaft Position Sensor
246
Like
Save
 Crankshaft Position Sensor')){kind=link}
- Tags:
Crankshaft, position, ReplacingCPS, Sensor
- Categories: Saturn
Comments
Write a comment
You must be logged in to post a comment.
I have plenty of questions that you don’t depict…
Hey I changed spark plugs n fuel pump n filter n ran for one day n died all
of sudden . Don’t near pump turn on wen I turn key. Plz help
I mEaNt wItH pRoPeR sHiFtInG aFtEr 25 + mph…tHaT mAkEs u tHiNk iTs tHe
Mass AiRfLoW sEnSor going bAd oR tRaNsMiSsIoN fAiLuRe w//rEvvInG uP tHeN
sUddEnLy seTTLiNg dOwN.cOrrEcT
yEs bUddY tHaT wAs a cPs 4 LT1 righT. pLeAse teLL mE hOw eXacTLy dO u kNoW
4 sUrE iTs oUt. DoEsN’T posItIon pRoPerLy aFtEr gOiNg 25mPh + wItH sHifTiNg
iN a 96’B.R.E.W.
Me again. Thanks for getting back to me. I watched this to see where the
crank sensor is. Question. Can I test this by hooking up a volt meter to
the fuel pump trunk connector. Then crank the car over? Just asking because
I did. And this time I maintained voltage to the pump.
I have a 2004 Saturn L300.3 Station Wagon with a V6 engine which runs like
a dream. This car is as if it was just driven off the show room floor. It
is the De-Luxe model with soft leather seats and door panels. CD and still
a casette player. The engine is very powerful, but the engine shut off last
night, then started again then shut off again and the engine light came
on.An analyzer at Autozone showed 0727 and 0700 codes. So I can do this job
myself then and how to clear the engine light?
The crankshaft position sensor on the vehicle is located on the transaxle
housing, facing the gear teeth of the drive plate.
I just changed the timing chain on my suzuki grand vitara (1999) and the
chains are aligned and everything but I still hear some rattle on it. It
shows Code P0355 and the Service Engine light keeps coming on. Could it be
the problem with the crank shaft sensor?
Looks easier than I thought it would be
Today I drove my car on the hwy. Standstill traffic the car stall on low
speed. First time it reset the car, dashboard light came on then car run
back on it own like nothin happen. Two mins later it happened again, but
this time car stall. I put the car on Neutral it start like nothin happen.
I went to autozone to do a code reader. Nothing and I dont have engine
check light. Idk if crankshaft position can solve the problem. I have 98
saturn sw2 with 74500miles. Can u tell me what I can do?
thank you for your help good sir!
I knew it! The thousands I spent on detectives was worth the accurate intel!
wow. this makes me see why ford stuck with the cvh engine for so long. cps
is right on the front of the block. cam position sensor is right on the
back. maybe 15min to change both of em if need be.
Excelente video, muy claro!!!!……..saludos desde Chile.
I do not work on any Benz to know what there problem areas are.
@deboy5319 I have never run into a broken one that being said i would start
by taking the starter out of the way.Then it would be trial and error on
the tools i would use.
what kind of vehicle are you demo on ?????????
@richpin06a i have followed the step by step and know when i tryden to
remove it i broke the sensor head and now its stuck and block and know i
need help trying to pull it out asap
So its not the one on the side of it ?
It is a Saturn S-series.
do you have the vehicle on a lift ?
also you can read the codes on the pt cruiser in car no need for them fancy
code readers I will do a video or if you want to do one drop me a pm and I
will tell you how its done so you can inform all the people out there that
count on you to help them save money and not get screwed by the dealers
On the 94 Altima it is Under hood, driver side, upper engine area, driver
side of engine, mounted in distributor .
I can not comment because i have not done this repair on the 99 Galant.
Possible causes of a P0355 Short to voltage or ground on COP driver circuit
Open on COP driver circuit Loose connection at coil or broken connector
locks Bad Coil (COP) Faulty Powertrain Control Module
wheres the crankshaft sensor located on a 1998 acura 2.3cl?? plus since my
car doesnt go over 3000rpms doesnt that mean its my crank sensor and its
hard to start. sometimes my car wont even start
Is the engine spinning over when you turn the ignition key to the start
position.
shut the Fuk up, LEARN TO READ clearly stated S-SERIES you got no knowledge
of cars calling someone i love silly? S-series are Saturns works with all
S-series Saturn. SHOW SOME RESPECT, This man saved most of us millions$.
Amazon is a great place to purchase a idem like this.
Hi rich.. I have a 2003 cadillac cts that is saying it missing 1 3 5 I
changed the spark plug and coil pack on that side “which is one whole unit”
and it still missing when i come to an idle..could it be the crankshaft
postion sensor..also i did notice that on the other side of the coil pack
which is 2 4 6 one of the spark plug cover has a hair line crack about 1
inch..could that make it miss fire on 1 3 5?
If anything they have a little “whitish” color to them, nothing dark or
black.
You say when reinstalling the new sensor you could pull the o ring off
wouldn’t that cause an oil leak
is the Crankshaft Position Sensor on a 1998 Sunfire in the same place
ruffly. or can you tell me where its at.. Thanks great video.
Using a scan tool would be the best way to turn off the check engine light.
What is the condition of your coolant temp sensor and its connector.
That’s a typical location for the Knock sensor I imagine?
If I just to the key on. It goes off at 3 seconds. If I crank it stays on
as I crank it. But with the trunk fuel pump connector plugged in I only get
10 volts. But unplugged I get the full 12 volts. But I also never hear the
pump. Or I should say not anymore. It ran from 10 minutes to 2 minutes and
now not at all. I think the pump just took a bad time to go out. I
rechecked the repair job at the PCM. It looks right. A Matco scan tool
found no codes.
You can remove the fuel pump relay from the interior fuse panel and jump it
from there to see if you hear the pump working.
what vehicle are you working on??? I have a 2008 Nissan Quest that won’t
start. Wondering if is the crank sensor. It takes a long time to start.
Thank you./
@richpin06a Checked ignition module put a new one on didn’t work. Luckily
the part store let me return it because they couldn’t test my old one for
me. It would have been $115.
@richpin06a, and thanks 4 all ur help man.
Just ramps.
@curtisalandavis Wow that could have blown the computer.In a normal car if
there was no spark after changing a cps i would look at the ignition module
as a possible cause.
It is a Saturn S-series.
It is located in the same general area below the coil pack on 2.2L engine.