http://www.1aauto.com/1A/TransferCaseShiftMotor/Ford/Explorer/1AFWM00009 1A Auto shows you how to replace the 4WD transfer case shift motor on a 1998 Ford Ex…
http://www.1aauto.com/1A/TransferCaseShiftMotor/Ford/Explorer/1AFWM00009 1A Auto shows you how to replace the 4WD transfer case shift motor on a 1998 Ford Ex…
You must be logged in to post a comment.
Yes Ive checked it and its good
You may want to check the level of the transmission fluid to see if it’s at it’s correct level. 1aauto.com 888-844-3393
I have a 1998 4×4 Ford Explorer 4.0 SOHC but the reverse doesn’t work and when I put the switch on 4×4 low I hear a clunking noise every few seconds and it doesn’t go into low. I have all gears except reverse in Auto or 4×4 High. Do you think I need a new Transfer Case Shift Motor? Thanks for the vid!
Good way to install and replace 4*4 transfer case shift motor ford explorer mercury.
That knocking noise is extremely bad for the engine. That means something inside is misfiring. You need to have that looked at immediately or you could risk destroying the entire engine.
I have a 98 Mecury mountaineer, when i accelerate or go after a stop it gives me a knock coming from the engine! what is it?
Thanks, I got it, it was in the right position, just a tight fit.
Normally you can rotate it with a pair of pliers to the correct position.
I am trying to put my shift motor back on, and it won’t fit back over the triangular piece which it rotates. I have checked that they are oriented properly, do you have any suggestions? Thanks
you can purchase them through our website. You can check us out at 1aauto.com
Where I can get a motor?
They should. This video should help you out in fixing the issue.
Do all the wire colors match upwith each other on both sides of the plugs? Someone has previously attempted this on mine and I want to make sure the wiring is correct. It looks like they broke a couple of pins and then wired them direct.
If you have a check engine light on you may want to pull the code to see what the code is pointing to. Hope this helps you out. 1aauto.com 888-844-3393
Help please, my 2001 Ford Escape just stopped and will not move in drive when place in drive mode. It will go into reverse with not problem. I thought it has something to do with me having the gear shift replaced on the transmission and not being repaired properly. Not sue! Please help.
The light should indicate if you are. You may also feel the front pull or grab while taking turns.
Thanks for checking us out. Have a great day! 1aauto.com 888-844-3393
just wanted to say thanks for all the videos you do they are very helpful!! i have a 02 mountaineer the awd is stuck on and making the back and front of the veh. wheel hope on hard turns Know its something to do with the awd transfer case do you think its possible that the shift motor could be the problem??Thanks and keep up the good work
If there’s a check engine light on, you may want to have the code pulled.
I have a 2000 ford explorer lost reverse …..all other gears work….Any suggestions
Hello to all,Need help I have a 97 ford explorer motor went to the bad,Had a machanic change the motor, My problem is it keeps brecking flex plates 2 different machanics change the flex plate 3 time keeps brecking HELP.
where is the 4 wheel drive actuator located on 1998 ford explorer
Most likely it is a vacuum leak. Check the rubber hoses around then intake manifold area for rubber parts that are splitting or deteriorate in your hand. A smoke test would work best to confirm vacuum leaks but are expensive to purchase.
It could be a bad actuator.
i have a 1998 ford explorer my 4wd kicks in and out would you happen to know what that could be ?
You may want to check the EGR valve to see if it’s working correctly. Also if there’s a check engine light on, pull the code to see what’s causing it to go off.
I have a ford explore sport the year is 99 i am not sure whats wrong with it i havent found a shop that knows every time its cold out my truck idles hard i mean really hard then it shakes and stops i go through starting it over 3-4 times before it idles at half way 1 i have to drive at 20 miles per hour because i press the gas and it barely goes and it is eating up my gas when the weather is nice it runs fine PLEASE HELP SOMEBODY!!!!!
i had to do the same thing on my 01 ranger (basically the same) in my case the 4wd would test good in the bulb test on start up and then the next day not. the problem was the switches inside the aluminum housing (like a wiper motor) went bad. works great now… let me know if thats a “normal failure” guys…. THANKS!