Buy Now!
New Camshaft Position Sensor from 1AAuto.com http://1aau.to/ia/1ACPS00034
For vehicles with electronically controlled timing, a camshaft position sensor relays important information to the computer to ensure the engine is running properly. A bad sensor may relay incorrect or no information, resulting in poor running conditions and trouble codes. This video shows you how to install a new camshaft position sensor in your 2003-2007 Infiniti G35.
• Check here for more videos on the 2003-2007 Infiniti G35: http://www.youtube.com/playlist?list=PLJVpHWuCEUX9INHZnLSy7u_jNSfqFBkNh
This process should be similar on the following vehicles:
2003 Infiniti G35
2004 Infiniti G35
2005 Infiniti G35
2006 Infiniti G35
2007 Infiniti G35
Tools you will need:
• Flat Blade Screwdriver http://1aau.to/opL/1AXAA00013
• Pocket Screwdriver
• 10mm Wrench http://1aau.to/oeb/1AXAA00010
• 10mm Socket http://1aau.to/onf/1AXAA00017
Subscribe: https://www.youtube.com/channel/UCWCdsftsTqYMO7cA_5Sc-yA?sub_confirmation=1
Check out our playlist:
Infiniti G35 3rd Generation 2003-07: https://www.youtube.com/playlist?list=PLJVpHWuCEUX9INHZnLSy7u_jNSfqFBkNh
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Hello is that bank 1 or bank 2?
I did the driver side but the connector will not stay on anyone els run into this issue ?
Thansk man I followed the instructions correctly and now I saved me 120$ thanks
Broooo how tf you took it off so easy been at it FOR DAYS
So only take the negative off right
Didn't take oil cap off before he put engine cover back on. Good luck putting oil in it if you need to top-off!
Great Video, My Question is should I sell my 2008 Infiniti M35 with ( 1. CAMSHAFT Sensor Seals Replacement, 2. Rear Main Seal Leaking, 3. Multi Oil Leaks, and 4. Service Engine Soon Illumating when the oil is low ) The car has 160,000 Miles. The Book Value is $2,300. My question is does it make sense to keep the car and repair these issues?
So, trying to figure out if my knock sensor is the issue for my RPMs not going past 3 RPMs while accelerating or this
Nice, straight forward and simple. Thanks!
Thanks, but would have been better if you could have filmed the bolt being removed, etc. I checked it out, but on my car, there wasn't enough room for me to get a socket wrench in there. I have no idea how you managed to do it.
how do know if you have to replace them both or just one ?
very good video. one comment on Bank 2 (driver side) sensor, the connector is different than Bank 1 (passenger side). The connector on Bank one has a tab you have to depress while pulling. there is no sliding lock.
other than that, and easy replacement doing it by feel.
Was this bank 1 or bank 2 that u did?
Where can I buy the camshaft sensor other than the dealer?
Tried doing cam shaft sensor replacement but the green tab doesnt stay in place when pushed down any recommendations