hey all idiot that have triede it this way the way to do it is to cut from
the lower side not the top spring on the complete opposite side of the end
of the coil, it will actually fit and work
He’s pretty much just making a video about why cutting the stock springs is
a bad idea. He’s not making the cheap decision for lowering the
car……dumbasses……
if u drive a g37 and too cheap to buy proper lowering springs, than u
shouldn’t be driving 1 at all. This is dangerous and ruins your vehicle
ride quality.
not hard to tell who owns a honda.. coilovers arent the only way to lower
your damn car — cutting springs been common practice for ever even on
high end cars and restored classics..
You are right providing you cut them correctly so you don’t heat them up.
The straight springs are so easy to cut and install but the graduated
springs pose a problem like in this case cause they just don’t sit right.
It’s the spring manufacturers that make you believe it’s dangerous. Don’t
do it if you don’t have any experience in any mechanical issues or get an
experimental spring to cut first. You will be safe if your springs are
immersed in water during the proccess.
FUUUQ ur speech is annoying. Cutting springs is not good 4 ne1 that dont
kno wtFUCK theyre doing. Like i told kid w the shit-box, (MEASURE)4 ¬e
the mount points topANDbottom. When u 1st throw them on, the fit wont look
perfect which is why u gotta be smart on how u reassemble it. round out the
end so it sits better on the perch. It looks “weird” @that point, i know,
but the weight of the car will set n keep them in their place,unless u try2
go airborne or any dumb shit like that.GOODSPEED
Most likely not enough to cause an issue as long as it’s done properly.
I’ll never recommend cutting springs because it’s a half-assed way of doing
things so if you’re going to lower your car and can’t afford coils buy a
spring kit or even go for a decent used spring kit to save some more money.
Everyone commenting on this video about how it’s ok to cut springs must be
ricers lol Why the hell would you want to cut your springs, its not 100%
safe and makes you look like an idiot when other people see that you cut
your springs. Sack up and spend the $250 but lowing springs if you want
your car lowered. They will lower the car more than cutting the springs
will, will be more safe when driving, and ride a hell of a lot better.
Idiots…..SMH
fuck ya mate. ive been cuting 4 cars springs, (usually half down so car is
low as fuck)!!! CUT SPRINGS IF U DONT HAVE MONEY TO BUY LOWERD SPRINGS!!!!
Thats the easy way! 😉 I don’t even take springs out when i cut them.
fucking easy!
who the fk goes around checking other peoples springs? i installed some
eibach springs and koni shocks on my car and not a single person has ever
said MAN NICE SHOCKS ANS SPRINGS!!
hey all idiot that have triede it this way the way to do it is to cut from
the lower side not the top spring on the complete opposite side of the end
of the coil, it will actually fit and work
+lexis256 are you fucking stupid???
i always cut the springs of my cars and never had a problems
the amount you cut is about ummmmmm…….. this much >……..< hahaha
He’s pretty much just making a video about why cutting the stock springs is
a bad idea. He’s not making the cheap decision for lowering the
car……dumbasses……
if u drive a g37 and too cheap to buy proper lowering springs, than u
shouldn’t be driving 1 at all. This is dangerous and ruins your vehicle
ride quality.
Good idea with the cooling water, but it wont get that hot with a tiny disc
grinder?
Perhaps cut half a ring from the middle, then weld together – cut & shut
idiots shouldnt work on cars
not hard to tell who owns a honda.. coilovers arent the only way to lower
your damn car — cutting springs been common practice for ever even on
high end cars and restored classics..
the strut lip would not be a wide enough lip get verry big washers thumbs
up
this will blow your shocks and struts
You are right providing you cut them correctly so you don’t heat them up.
The straight springs are so easy to cut and install but the graduated
springs pose a problem like in this case cause they just don’t sit right.
It’s the spring manufacturers that make you believe it’s dangerous. Don’t
do it if you don’t have any experience in any mechanical issues or get an
experimental spring to cut first. You will be safe if your springs are
immersed in water during the proccess.
I cut the springs on my car and it sat very nice and looked better. also it
never bottomed out or rub the tires. DO IT
FUUUQ ur speech is annoying. Cutting springs is not good 4 ne1 that dont
kno wtFUCK theyre doing. Like i told kid w the shit-box, (MEASURE)4 ¬e
the mount points topANDbottom. When u 1st throw them on, the fit wont look
perfect which is why u gotta be smart on how u reassemble it. round out the
end so it sits better on the perch. It looks “weird” @that point, i know,
but the weight of the car will set n keep them in their place,unless u try2
go airborne or any dumb shit like that.GOODSPEED
FUUUUQ your shorthand is annoying and hard to read.
Cutting springs is not the way to go
dont worry we get free camber :DDDDDDDDDDDDDDDDDDD
would it be a noticeable drop?
this guys chilled not slow.
Most likely not enough to cause an issue as long as it’s done properly.
I’ll never recommend cutting springs because it’s a half-assed way of doing
things so if you’re going to lower your car and can’t afford coils buy a
spring kit or even go for a decent used spring kit to save some more money.
Everyone commenting on this video about how it’s ok to cut springs must be
ricers lol Why the hell would you want to cut your springs, its not 100%
safe and makes you look like an idiot when other people see that you cut
your springs. Sack up and spend the $250 but lowing springs if you want
your car lowered. They will lower the car more than cutting the springs
will, will be more safe when driving, and ride a hell of a lot better.
Idiots…..SMH
fuck ya mate. ive been cuting 4 cars springs, (usually half down so car is
low as fuck)!!! CUT SPRINGS IF U DONT HAVE MONEY TO BUY LOWERD SPRINGS!!!!
Thats the easy way! 😉 I don’t even take springs out when i cut them.
fucking easy!
who the fk goes around checking other peoples springs? i installed some
eibach springs and koni shocks on my car and not a single person has ever
said MAN NICE SHOCKS ANS SPRINGS!!
ur hahahahahahaha LOLOLLOLOOLOLOLO jst put them back il work fine
cut them right
I just want to trust you because of your accent!
his stupid ass still posted the video lmao