Get a fuel line disconnect set on Amazon→http://www.amazon.com/gp/product/B000W0UZHG/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=…
Get a fuel line disconnect set on Amazon→http://www.amazon.com/gp/product/B000W0UZHG/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=…
You must be logged in to post a comment.
){kind=link}
Happy Birthday, thanks for the video i’ve been watching a lot of yours
learning a bit or two
I have a big 4×4 and find it so hard to get into the engine compartment to
work on anything…so I have been eyeballing a topside creeper off amazon”
Traxion 3-100 Foldable Topside Creeper” to save my knees and back…seeing
you on your knees up on the rad support hurt me just watching and looks
like you need a topside creeper too…maybe get one do a review and when I
buy one I will use your link to get mine…how about it? $200 well spent
I’m hoping.
i have a rough idle and stall when the engine is cold when i start mine in
the winter
but when it warms up a bit 30 or so seconds it seems to run fine. is that
what this truck was doing?
just lik the 6 liter i just did i didn’t do the intake i just ripped the
engine out
Great to see diagnostics before you jump in and replace the bad part.
Another winner video, Brian.
“you better pick that up, it’s your wife” and Brian just ignores it!
I love your commentary. 11/10 sir!
Happy birthday
Happy Birthday Brian
Happy birthday!
heh, my friends are always gloating about their new vehicles but my ’94
will still be running when their plastic car is being recycled
I’ve used wobbles for years. Plus a lot less expensive than a Snap on set
of flex sockets.. Great Vid as usual.
happy birthday Brian, great videos, and we all appreciate guys like you
posting this stuff, makes us smarter and gives us some confidence! I have
a 98 dodge ram and known for blown plenium gasket, and after a drive in a
snowstorm and using 4×4, it makes a humming noise with acceleration, sounds
like coming from engine, and water pump weeping hole isn’t leaking, in fact
nothing is at all, fluids are all topped up too… suggestions? water pump,
idlers, alt?
Hello Brian… I have a question, I have a 2000 silverado 5.3 and coolant
is going slowly to oil, the cooling system is clean, heater works fine, no
smoke out of the pipes, No overheating, engine looks clean, no leaks , I
thought it was a minimal crack on the heads and decided to try Blue Devil
but didn’t work, so should I replace head gaskets?, will it fix the
problem ? if you can give me an idea what would cause this I would really
appreciate it ( no check engine light on either )
Thanks in advanced
great video mann!& HAPPY BBIRTHDAY!top notch video as usuall,i currently
sat up recovering from an op on my right lower leg now ive watched this
makes me want to fix my rangerover lol
Happy Birthday Brian! You’re like an automotive astronaut… you’ve got
the right stuff. ;)
Excellent video Brian!! I watched the whole thing too! Videos like this
give me the confidence to tackle projects that I would take to the shop,
thanks. Love the end too, let it snow!
happy belated birthday brian!
epic beard action
Awesome video! Your instructions helped tremendously! (probably wouldn’t
have done it myself if I hadn’t viewed your video) My 04 Suburban purrs
like a kitten now!
love your videos! subed for life! i have a 04 4.8, its not throwing any
codes, but she dogs down when she start up (non cold start) and if i turn
the steering wheel and/or press the brakes she dies and thin dose not like
to hold the idle, could the gasket be the issue?
Happy Birthday!
till 120 in good health and spirit a very happy birthday.
I have a car from mom a 1998 opel corsa cdx.also as holden barina.
I don t have the idiot plastic cover.its a very simple 4 cylinder motor
most work un do bolts and the connections.wich at opel dealer they charge
you
the hours they work on it.
think they put plastic cause car need be lighter gas is expencife.you look
at tesla
or Bentley lot of plastic
wander
is a iroc and trans am gta easy to work on ?
Happy Birthday Brian!! I hope it was a good one.
Happy birthday !!!
I can see you are getting good with your Spanish. Good job Brian, not
Brian, great job– regarding the truck running worse in the winter with
increased vacuum leak don’t you feel the colder temp shrinks things causing
more clearance between the head and intake thus vacuum leaks vs warmer
weather where distortion isn’t such a problem?
Great video.
Noticed you using the Autel Maxidas DS708.
We’ve had one for a year in the shop and it has worked great.
Most excellent on Euro cars and Asian.
click click click click no snap snap!
nice video as always thank you for taking your for making it and happy
birthday brian
happy 18th mate !
I’m getting 0171 and 0174. Got a 2003 5.3. Idles bad when cold. Warms up
its fine. Other than that runs like a stallion. What is the cost to do what
you did at an independent shop? No way will I take it to a dealer.
Hopefully I just have a hose bad. Thanks.
sweet
That has nothing to do with E85 ethanol that is just from putting plastake
crap were it has no business being.
Chinese finger trap believe it’s the first time I’ve heard that lol
brian that was a very easy job on my 4.8 2002 silverado 4wd with your video
thanks better than gm service manual
Happy Birthday Brian! Wishing you many more.
Aloha
Happy birthday!!!!