Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com http://1aau.to/ia/1ASHF00525
1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning wheel bearing hub. This video is applicable to the 14, 15, 16, 17, 18, 19, Chevy Silverado
This process should be similar on the following vehicles:
2014 Chevrolet Silverado 1500
2015 Chevrolet Silverado 1500
2016 Chevrolet Silverado 1500
2017 Chevrolet Silverado 1500
2018 Chevrolet Silverado 1500
🔧 List of tools used:
• Pry Bar http://1aau.to/ofR/1AXAA00020
• 15mm Socket http://1aau.to/ouJ/1AXAA00015
• 35mm Socket http://1aau.to/om/1AAST00005
• Brake Caliper Hanger http://1aau.to/oaC/1AXAA00084
• Needle nose pliers http://1aau.to/odf/1AXAA00051
• Needle nose pliers http://1aau.to/odf/1AXAA00052
• 1/2 Inch Air Impact Gun http://1aau.to/obD/1AXAA00252
• T30 Socket
• 1/2 Inch Breaker Bar http://1aau.to/obL/1AXAA00078
• A Piece of Pipe (for leverage)
• Ratchet http://1aau.to/ows/1AXAA00016
• Socket Extensions http://1aau.to/ouJ/1AXAA00015
• Torque Wrench http://1aau.to/onK/1AXAA00044
• Anti-Seize Grease
• Brake Parts Cleaner
• Cloth Rags http://1aau.to/odn/1AXSS00035
• Rust Penetrant
• Center Punch http://1aau.to/oa7/1AXAA00055
• File
• Hammer http://1aau.to/ofP/1AXAA00091
• Pick http://1aau.to/oei/1AXAA00037
• Wire Brush http://1aau.to/obY/1AXAA00079
Subscribe: https://www.youtube.com/channel/UCVvE8kQTuZEykvMFZBVzftg?sub_confirmation=1
Check out our playlist:
Chevy Silverado 2014-2019 3rd Generation: https://www.youtube.com/playlist?list=PL37d7oWG6wDC1amY7nx965nDSCIKHMRsI
Chevy Auto Repair Videos: https://www.youtube.com/playlist?list=PL37d7oWG6wDDg0_NWAHajg49IsosO4Vz9
For More Info visit us at http://1aau.to/h/bCC/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Visit-1AAuto
√ Do it Yourself
√ Save Money
Is it a good idea to replace both front hubs if one goes bad?
FYI disconnect your battery before you unplug anything because It may send an error code to your computer and it will cost around $200 just to reset it.
I use an ole c clamp and the old pad to push it back
I just replaced both of my hub bearing assemblies yesterday on my 2017 Silverado. I am now getting a stabilitrack code and an abs light on my dash. Is that something that can be reset with a scan tool?
I followed every step and it went smoothly but now my abs light and stabilitrak is on and wont turn off, what might be wrong?
Going to be doing this over the weekend. How much do you want to bet mine doesn't come off that easily.
he a pro or he have done this so many times for the video he kno what he doing
Where can I get all the torque specs for my vehicle
With parts, does it matter between trim models? I have a 2015 high country silverado 4 wheel drive.
Thanks for this. I just had an alignment done on my truck a week before replacing the passenger bearing. Should i need a alignment again? 2016 sierra
would a bad hub cause the abs light to come on?
Is the socket required 35mm or 36mm? Everything that I've found online says 36mm.
Why wasn't the caliper taken off all in one step/piece?
Is it the same for the rear wheels?
How long of a job is this? Trying to get an idea of what I’m looking at for labor before I call the shop as I don’t have the tools to do this myself. Thanks for any info!
I don't know who taught this guy to use a hammer on a threaded shaft without using the nut to protect the threads and end of the shaft so you don't mushroom the end of the shaft. Also if you look at the rotor there is a threaded hole that you can put a bolt in and tighten up to break the rotor loose.
A link to the bolts please?
Hey sir or anybody I have ?? I have a 02 Silverado an the cv axles has play I’ve changed the axles do u think it’s the hub
Thank you for your video
This is fake!!! He's not dirty, hasn't said one cuss word, or thrown a wrench.
Are the bearings inside the hub not serviceable? I mean its a $150 hub vs a $20 bearing that goes inside it.