http://www.1aauto.com/1A/wheel-bearing-hub-front 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front whe…
http://www.1aauto.com/1A/wheel-bearing-hub-front 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front whe…
You must be logged in to post a comment.
){kind=link}
I installed the wheel hub barring and made sure everyrhing was tight bolted and some how something is still lose the car shakes when I brake
Thanks alot. I can’t find very much videos for 97-03 grand prix’s. You saved me from going to the shop.
you guys didnt need to remove the balljoint to access hub bolts? some videos show needing to remove the ball joint on the GP.
im going to be changing my bearing tomorrow. hopefully goes as planned in this video
You should be able to tell by looking at the ABS wire on the back of the hub. The dealer could also run the VIN number and tell you what came on your vehicle. We carry both hubs with free shipping in the lower 48 states on our website 1aauto.com.
I have a 01 Grand Prix GT 3.8, is there anyway to find out whether the HUB assembly has a plastic or steel wire? I would just like to know before I go buy the parts…
We found out the issue. It was a worn out front Sway bar Link
You may want to check all of the steering and suspension pieces to see if anything is worn out. Hope this helps you out. 1aauto.com 888-844-3393
Hi. I need a little help. My dad’s 2005 Chevy Impala is making a weird noise near the right front suspension. Every time he hits the brakes, it will make a loud pop. I need suggestions. Any ideas? Thanks!
When you replace the studs you really should not need anything else when you remove the hub to do the install.
how come you didn’t just remove the axle from the hub? I have a honda civic and I’m fixing to remove the hub to replace a broken wheel lug stud; I have to remove the hub because its small and driving the lug hits the part where the hub attaches.
Here the question, I’f I remove the hub, are there parts needing replacement other than the wheel stud I mentioned, are there seals that I should replace?
Thank you
The issue could be with the axle on the left side of the vehicle since the noise only happens during right hand turns. Axles go out for numerous reason but weight is never an issue with axles.
Hey man great vid I just had a quick question on my old car I would always have to put front wheel bearings it was a 92 ford explorer I sold it and I got a 03 trailblazer and I think my front wheel bearing are bad just on one side tho every time I make a right hand turn I hear a noise but when I just drive or turn left theres no noise you think it could be the bearing also I’m a big guy could that be a reason y I don’t have good luck with bearings ?
It should take around an hour.
How long does it take a professional to replace one on the front driver side of a 2000 Toyota Rav 4?
Thank you.
Great video, was very helpful and saved my weekend.
Great videos! Much appreciated! Thanks!
Both sides. We carry a nice brake pad and rotor kit for these cars, you could follow the video and change them yourself. It’s not to hard to do. 1aauto.com 888-844-3393
Thanks you for resonding, is that for both front side or just one side?
It normally runs around $300+ depending upon the hourly rate of the shop.
how much does it cost to bring it to the garage to get it fix? Thanks.
You may need a bolt extractor to get it out.
how to i take out a broken head screw bolt
It may help to gain you a little more clearance.
You’re welcome. On vehicles that have over 100,000 on them it doesn’t hurt to replace both bearings at the same time if one goes bad. Usually the other side isn’t to far behind it if it hasn’t gone bad already. Sometimes it’s easier when you have all of the tools out.
my car made noise I thought wheel bearing as the comments on here stated I turned the wheel the left at speed and got way worst then I read must be right brearing im guess these cars bearing need replaced at about 120,000 miles just turn ur wheel listen works on front A1 saved me thank you
Thanks for checking us out! Have a great day. 1aauto.com 888-844-3393
a1 is very good co ty
We carry brand new wheel bearings on our website 1aauto.com for your grandprix. All of our auto parts include free shipping in the lower 48 states. Have a great day! 1aauto.com 888-844-3393
my grandprix made noises for a year now I know it the front right wheel hub bearing been riding on a bad one for a year
You’re welcome, thanks for watching. Have a great day! 1aauto.com 888-844-3393
Thanks
The issue sounds more like brake issue than a wheel bearing. If it happens only under braking then it is only related to the brake system.
hi my right side wheel on my Nissan Maxima 2000 makes noise like a grinding or sometimes a squeaking sound when i use soft braking do u think its the hub bearing is worn out?even when i stop i can feel my steering wheel shake my brake disc is good and brake pads too. the video shown here is it the same way to get it off on my car????
You’re welcome. Have a great day! 1aauto.com 888-844-3393 FREE SHIPPING in the lower 48 states on ALL AUTO PARTS!!!!
now i know whats causing my track off light to come on and why my car jerks when i give it gas. the guys at firestone didnt place my hubs back on correctly! thank you auto1 -mike