How-To Series: ZL1 1LE Rear Spoiler Install // Carbon Fiber Wing

How-To Series: ZL1 1LE Rear Spoiler Install // Carbon Fiber Wing

This video will cover how to remove the factory OEM spoiler from your 6th Gen Camaro with a post style spoiler (ZL1, SS, etc.) and replace it with the ZL1 1LE style spoiler. In this video we will remove the factory ZL1 spoiler and replace it with the Anderson Composites 1-piece Carbon Fiber ZL1 1LE rear wing.

Affiliate Links:
2016-2024 Chevy Camaro ZL1 1LE Full Carbon Fiber 1pc Rear Spoiler:
https://bit.ly/3PmA3uu

Milwaukee 1/2” Drive Socket & Wrench Set:
https://amzn.to/430BKlz

Milwaukee 3/8” & 1/4” Drive Socket & Wrench Set:
https://amzn.to/3Mztv98

10mm Swivel Wrench:
https://amzn.to/45QFas4

Magnetic Pickup & Tray Tool Set:
https://amzn.to/3P6sJlv

Panel Removal Tool Set // 200PC:
https://amzn.to/3qZCrOo

Plastic Blade Trim Removal Tool:
https://amzn.to/3EoHomX

3M Adhesive Eraser Wheel:
https://amzn.to/3R4Rlxq

3M 06394 // Strongest Automotive Adhesive Tape:
https://amzn.to/44CaZUv

LED Side Markers:
https://amzn.to/42RBzJ2

Lift Pads:
https://amzn.to/3s3FwtT

ZL1 Addons Premium Magpuck:
https://tinyurl.com/bd9kp5cm

Rotofab CAI for Camaro w/ LT4 V8:
https://amzn.to/43jSmW8

Rotofab CAI for Camaro w/ LT1 V8:
https://amzn.to/3ZRchbT

Corsa Extreme Axle Back Camaro V8:
https://amzn.to/3BSxdG3

Corsa Carbon Fiber CAI for ZL1:
https://tinyurl.com/wr8s4rx8

Silicone License Plate Frames:
https://amzn.to/3BMnoH5

Chapters:
0:00 – Intro // Overview
0:36 – Tools Needed
1:35 – Shout Out to Matt // Car Owner
2:00 – Pop the Trunk // Location of the Factory Bolts
2:30 – Removal of the Trunk Trim Panel // Bee Cameo
4:00 – Loosen the Factory Spoiler Nuts
5:40 – Squeeze Spoiler Clips // Outer Spoiler Posts Only
6:20 – Removing the Factory Spoiler
6:45 – Cleaning the Adhesive Off // Plastic Blade and 3M Eraser Wheel
8:15 – What Comes with the Anderson Composites Spoiler? // What Do I Need?
9:05 – How to Use the Indexing Posts // SS 1LE or No Factory Spoiler
10:25 – Placing the Weather Seals Around the Spoiler Bolts
11:00 – Installing the Anderson Composites Carbon Fiber Rear Wing
12:50 – Reinstalling the Trunk Trim Panel
14:05 – Reinstall Trunk Latch Cover
14:37 – Outro // Beauty Shots

*These are affiliate links to the products. I make a small commission on anything purchased from my links.*

**Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use of the information I share in my videos. (FollowMyLine17) assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not (FollowMyLine17) or any business affiliated to (FollowMyLine17).**

321
Like
Save


Comments

mike Selchow says:

Glad to know there’s another zl1 in Minnesota. I’ve only seen 1 other and it was a convertible

matt says:

Lools good, glad mine came with this! I like the black post on the stock one better than the carbon fiber post. I might just be use to the stock version but the carbon fiber post look out of place.

Cryptoinvestor6878 says:

Good looking wing, loved the detailed instructions.

Comments are disabled for this post.