More repair videos on the links below:
Ambient air temperature sensor testing and repair Volvo VN
https://www.youtube.com/watch?v=T_35TnWszcA
Honda GX 390 oil change pony motor:
https://www.youtube.com/watch?v=5BcidS0AvYg
Meritor power divider removal and disassembly:
https://www.youtube.com/watch?v=HV5ERSM85hg&t=2s
Peterbilt Brake Valve Replacement:
https://www.youtube.com/watch?v=G8rNCBlseJA&t=197s
Meritor differential disassembly:
https://www.youtube.com/watch?v=DOde9jJznVQ&t=5s
Meritor differential removal Volvo Truck:
https://www.youtube.com/watch?v=6rmoV2Ogenc&t=1s
Hendrickson wide bushings replacement:
https://www.youtube.com/watch?v=YbHngtFHj_I
Eaton transmission and clutch removal:
https://www.youtube.com/watch?v=jiRbWHTRc_Y&t=384s
Volvo D13 Radiator replacement:
https://www.youtube.com/watch?v=kl9n7pAqCiY&t=222s
Carrier reefer unit exhaust manifold replacement:
https://www.youtube.com/watch?v=ER6HieDvFvU&t=231s
Rear axle differential repair Volvo Truck:
https://www.youtube.com/watch?v=P4ubQZb907M&t=48s
#Hendrickson suspension bushings replacement:
https://www.youtube.com/watch?v=dahYaqLFe9o&t=2s
Hendrixon Vantraax frame brackets replacement:
https://www.youtube.com/watch?v=bspzQ5O1NSQ
Building #RGN Fifth Wheel Frame Ramps:
https://www.youtube.com/watch?v=pezzivebSVY
Welding aluminium tool box for headrack:
https://www.youtube.com/watch?v=-4S_13eJ4hM
Fan mail send to:
5938 NE 2nd ct.
Renton Wa
98059
Liked the video it showed everything. When you make another video give a little more explanation, maybe even give some torque specs of the fasteners on the vehicle your working on. Overall great job!
Front Full Open Method Kingpin Open
did a good job how to open
instead of tapping the bearing with the chisel just put big enough socket over it and hammer it equally
Did ur truck shake while driving thats the reason u replaced it?
What the mileage of the truck ?
Now Borris ready to conquer elk mountain.
What size of socket need to be used with kingpin nut? And for top cover? Thanks!
Awesome job
How long a king pin usually last ?.
Is it safe to drive with worn king pins?
Gracias por traducirlo. Hacer mas videos para vnl traducido.
Excellent!!
Great video also great mechanics, good luck for all you do!
Don’t you have to check the clearance somehow to make sure you have the proper shims installed?
You are practicing work i think
You didn't filled grease manually in the taper bearing,and not cleaned the axle…worst watching
I did the same king pin job and somehow I think i didn’t do it right because when I grease it at the end no grease came out between the axle and the spindle torqued the nut to 250 lb-ft. and it was very hard to turn the hub by hand. so I have some questions if you don’t mind.
Aren’t you supposed to clean everything with a wire brush?
Do you install the bottom seal and bushing on the spindle or you put them on the kingpin?
Are you supposed to use any of the shims that come in the kit? If yes how do you know which size and where?
Are you supposed to grease the bearing before installing?
And last the nut on top are you supposed to torque it to specs if yes how much torque?
How many miles your truck had when you replaced king pins?
How do you figure it out you need change the kingpin? Any leakage or vibration or sounds warn u out or engine light? And what is the main reason for this issue? Such as bad bumpy roads or to much hard rolling steering wheel. You are wonderful and keep going. Молодец
Bravo baieti !
Great videos brother I am enjoying the repairs and learning a lot from your channel keep the videos coming I like Volvo trucks and peterbilt trucks and kenworth and international and mack I will be certified soon and get my CDL soon keep the videos coming God bless