Buy Now!
New Radiator from 1AAuto.com http://1aau.to/ia/1ARAD00925
This video shows you how to install a new TRQ radiator in your 2011-2018 Volkswagen Jetta. Overheating is a sure sign there’s something wrong with your cooling system. A leak, rust, or obstructions are all cases that may require a radiator replacement. Install a new TRQ radiator that’s engineered to fit your vehicle with the help of this video.
This process should be similar on the following vehicles:
2011 Volkswagen Jetta
2012 Volkswagen Jetta
2013 Volkswagen Jetta
2014 Volkswagen Jetta
2015 Volkswagen Jetta
2016 Volkswagen Jetta
2017 Volkswagen Jetta
2018 Volkswagen Jetta
Tools you will need:
• Flat Blade Screwdriver http://1aau.to/oa/1AXAA00013
• Pocket Screwdriver
• Pry Bar http://1aau.to/oa/1AXAA00020
• Trim Tool Set http://1aau.to/oa/1AXXX00004
• Pliers
• T25 Socket http://1aau.to/oa/1AXAA00008
• T30 Bit http://1aau.to/oa/1AXAA00008
• Ratchet http://1aau.to/oa/1AXAA00016
• Drain Pan http://1aau.to/oa/1AXAA00320
• Pick http://1aau.to/oa/1AXAA00037
Subscribe: https://www.youtube.com/channel/UCWCdsftsTqYMO7cA_5Sc-yA?sub_confirmation=1
Check out our playlist:
Volkswagen Jetta 2011-2018 6th Generation: https://www.youtube.com/playlist?list=PLJVpHWuCEUX_5CtiXTIkGICfCUObGa2tc
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
){kind=link}
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
What tools are required for this job
Is this process the same for a 2018 passat? Or should i be expecting somethings extra?
4:50. You should make a short dedicated only to this little mf’er connector.
Thank you so much for this video.
This video was a lifesaver. The instructions are clear, well spoken and easy to understand. I’ve watched many YouTube videos on various auto repairs and many are very difficult to listen to and to understand and the camera work gives you motion sickness. This is not the case here. The camera work is outstanding and the speech is clear and easy to understand. This is an excellent video.
There were some differences between my car and the car used in this video. My car has the 2.5 5-cylinder engine. With this engine, the fan assembly and the radiator come out the bottom of the car rather than the top as shown in this video. I found this out quite by accident when I was trying to figure out how to get the fan assembly up and out the top. Just when I had decided that I needed to remove the upper core support, the fan assembly slipped out of my hands and dropped right to the floor. Hmmm. Okay. So I got that out of the way and then lowered the radiator out the same way. The radiator was a little trickier because I had to work it between the lower core support and the A/C line. They both went back in much easier than they came out.
This video really made this job much easier! Thank you!
some aftermarket ones are less then 1/4" too thin, not allowing the front and upper plastic trim pieces go back on
For the other DIYers, do not put the body work back together in case you have a leak. It's annoying that to take that off again to fix something
If I don’t have the vacuum tool, what’s the process for making sure to get all the air out? Fill it, run it for a moment, then top it off and repeat ?
Hi, my golf mk6 coolant radiator is minor leaking, thank you for your video. My question, if I only need to replace the radiator, must I take off many front parts? like headlight? front steel bumper core etc. it looks like need to take off most of front parts, in order to just take out the radiator? is it possible that just take out radiator from back (between fan and engine gap)? Thank you.
Is the lower radiator hose on the driver side?