In this video, I show you how I installed my kill switch for my 1999 Toyota 4Runner. It taps into the fuel pump wire and kills power to the fuel pump thus preventing the vehicle from starting.
See also my 5 ways to prevent car theft video for more ideas on theft prevention: https://youtu.be/QmeRDWG8Scc
3rd Gen 4runner Mafia Group: https://www.facebook.com/groups/3rdGen4RunnerMafia/?fref=nf (Look for Minh Bui)
Some products I mentioned in my video:
Kill Switch (pick your favorite): https://smile.amazon.com/s?k=12v+switch&ref=nb_sb_noss_2
14 AWG Wiring (you just need one color): https://amzn.to/3mKUfqw
Connection Kit: https://amzn.to/2xFbBQ9
Wire Cutters: https://amzn.to/3iW2GhD
Heat Gun: Use a blow hair dryer
#killswitch #diy #hatethieves
► Buy me a coffee if I helped you with this video! https://www.buymeacoffee.com/phorunner
► Support this channel by buying some 4Runner Merch! https://teespring.com/stores/phorunner
Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use or unauthorized modifications of this information. I assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond my control, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not me. Enjoy my videos.
As an Amazon Associate, I earn a small commission from qualifying purchases. This cost you nothing and helps support my channel! Thanks!
Thanks for the video. I can now say the same wire is in the 01 4Runners and this worked great. Hardest part was finding a good spot for the switch and fabbing up a mount.
Just to wanted to add some value and say that 16 gauge primary wire has been working just fine, thanks again!!
What color wire is for 06 4runner??
Can you hook it to your starter wire so it won't even turn over?
In my pee brain the circle on the switch makes more sense on it's running. A circle shows a continuous cycle in my pee brain. The strain line represents in my pee brain an intermetten situation. I've always been confused about this. Lol
You can use a torch to heat shrink too.
Does the light turn on the switch. when it’s on the on position? Thanks for the helpful video
would this work on a 2010 corolla? ik it’s a pretty big difference but i’d like to know
Good looking rig. Im gonna try this on my '97 t100. Thanks for the vid.
2002 model doesn't have the blue and orange cable
Is this the power wire of the fuel pump? Is it safety to put the switch on the ground side of the fuel pump?
How do you not have a million subscribers yet
I think a photo of my Ex's Momma in the cab will beat any switch install.
Same for 1998. Though the wire is thicker than I imagined. I might solder the wires and use liquid electrical tape, I'm not as sure of my crimp skills as I am my soldering skills
Can anyone verify that the 5th Gen 4Runner fuel pump wire is blue with the orange stripe as well? Cheers y'all…
Thank you for this its been hard to find what wire to cut into
I’d like to do this on my 4Runner. I’ll check if my wires look the same..
Mannnn you are the best. This video is great
Dont share your location. Dont dont.
Could you please tell me what car alarm should I use for my 2001 regular 4runner?
Can you do the andy mod tutorial?
Excellent kill switch installation bro
If anyone decides to do this, before you begin work on electrical components, you should disconnect the cars battery and wait a few minutes for all capacitors to deplete, otherwise you run the risk of blowing fuses or destroying electrical components when you make mistakes.
I blew an ECU fuse trying to turn off my TMPS light and my car wouldn't leave park. I am lucky a fuse blew and nothing worse.
Awesome video. I have a 96 myself and i'm thinking of doing this to my vehicle. I don't know exactly how you wired it to the button. So you cut the wire, and connect a longer wire on each end of that (cut) wire, then connect those two (extended) wires to the button to hide it? I wish i could post a picture here 🙁
I have a 5th Gen. Is the fuel pump wire in the same spot as your 3rd gen?