Do you have a Saab 9-3 no crank no start situation❓ Your Saab 9-3 won’t crank AND no clicks, NO life from underbonnet❓ Try this solution to start the car. Saab 9-3 common problems. #Shorts
👉 How to FIX Saab 9-3 no crank no start: https://youtu.be/MmZalE0eiYE
Here’s your Cyclone Cyd Saab top tip of the holiday weekend. My Saab 9 3 won’t start I hear you cry❗ If you are getting no crank no start no click OR no crank no start no communication from your 9-3 when you turn the key, this video short will explain one possible cause that is definitely one of the Saab 9-3 common problems and is extremely easy to test for.
In another video, I show you how to carry out a strip down and repair this problem without buying a new module (which is what any garage would advise 💰💰). 👆 click on the video link above.
☕ Support the channel here: https://www.buymeacoffee.com/CycloneCyd ☕
💡 Subscribe and hit that bell 🔔 to learn more about looking after your car.
Learn more about looking after your car:
🎥 How to replace a CV [constant velocity] joint boot with a split kit: https://youtu.be/MuEgTqUCBDI
🎥 Don’t let your fuel filter end up like this 100,000-mile old example:
https://youtu.be/8aZLTbG993Y
🎥 Battery & alternator care in this playlist: https://www.youtube.com/playlist?list=PLOaePmzqZNJ24dTPG6x570Pze_D4Cxy6F
Everyone should have a tyre pressure gauge in their glovebox:
http://bit.ly/Tyre_press_guage
http://bit.ly/Pressure_Gauge_2
I personally prefer a stirrup pump to a foot pump (I use the same one for my bikes and cars)
http://bit.ly/Tyre_stirrup_pump
Are you trying to grow your own YouTube channel? I use TubeBuddy, try it out for FREE:
https://www.Tubebuddy.com/CycloneCyd
Gear I use in filming and production:
https://bit.ly/CC_Gear
My videos are edited with Filmora X – try it for free
https://bit.ly/Filmora_X_try4free
Thank you
saab 9-3 no crank no start, saab 9-3 won’t turn over, saab 9-3 wont crank, saab 9-3 wont start, saab 9-3 common problem, no crank no start no click, saab 9-3 common problems, my saab 9 3 won’t start, no crank no start, no crank no start diagnosis, no crank no start no communication, u0212, u0212 saab 9-3
#savesaab #savinganothersaab #saab #saabaero #saab93
){kind=link}
Thanks big man, you saved lots Ghana cedis, am in Ghana and you have saved me a lots Thanks again
Only track control light comes and stay while driving,sometimes when starting,sometimes car starts at first attempt,sometimes must insist.speedo unstable. Any suggestion? No abs light,no engine light.
update,,,,replaced battery,car started and worked for a while,problem returns,now cranks but no start.
Thank you. You are a life saver. I was on a trip and this happened. Saw this clip, removed the connector. I could not find cables, but when I re-connected, it started right up. I did have a check engine light and stability control system failure warnings for a day, but went away as I was going to get the codes read. Thanks again.
I've got a 93, starts but the gages on the dash switch off and head lights go into disco mode, any suggestions please?
my saab cranks but doesn’t start. starts up with starter fluid. i’ve got code “P0725” “engine speed input circuit”
this guy cranks his hog
Awesomeness
I had stability and traction control warnings in the dash. I did this and those went away, but the starter still wouldn't do shit. It just began one day after a drive it died at idle in the parking lot. Started it again and it idled for about a minute and died again after that, it would start sometimes and not even crank other times. Now it won't crank at all.
Nice one, been trying to start it for 20 minutes, saw your video and just wiggled the connector to the ABS ECU and it started first time. Might be why I occasionally get warnings about traction control disabled (or something along those lines!)
Those 4 pins btw is the CANBUS in and output pins, meaning if one of them crack or comes undone, the rest of the car cannot communicate with anything on the PBUS as the ABS module is the first junction in the harness
Hey there I have Saab 2007 2.0L T is giving me code p0606 for pcm I have to change the pcm ? Thanks
Thats a great tip. I've had problems with a number of ignition modules that stop working or very unreliable, very inconveniently. Is there a shortcut/easy way to install a push button start as backup?