Car Fix DIY Videos

This video is all about removing the grille and other accessories from your old bumper and transferring them to your new bumper. It’s quite simple with the correct tools.

Where to buy: https://bit.ly/16ElantraFrBumper

0:00 Start
0:08 Intro
0:19 Remove bumper absorber
0:44 Top grille removal
1:41 Lower grille removal
3:36 Fog light bezel removal
4:40 Drill out the rivets for headlight bracket
6:07 Rivet in the headlight bracket
7:52 Install the top grille
8:55 Install lower grille
11:03 Fog light cover install
12:15 Install bumper absorber
13:28 Outro

On this bumper, we will be removing and install the bumper absorber, the grilles, two brackets under the headlight, and the fog light covers. The brackets near the headlights are secured by rivets. Rivets aren’t scary when you know how to remove and install them.

TOOLS NEEDED:
The tools you will need for this job will be a Philips screwdriver, a drill, and a rivet gun (pneumatic or handheld).

Hopefully, you have already removed your bumper. Start with the bumper absorber or the giant foam piece that sits between the bumper cover and bumper bar. It’s held on by a clip on each end that looks very similar to a razor blade. Just simply pull these off. The top grille is held on by Philips screws on each end and the grille snaps onto tabs on the bumper. On to the lower grille which is very similarly secured into place like the top grille. Remove the screws on each end. The lower grille will have two screws on the bottom of the grille as well. Pry the grille off by pushing the tabs away from the grille with your fingers or flat-head screwdriver. The fog light covers or if you have fog lights are attached with screws onto the bumper. Repeat on the opposite side. If you have fog lights, detach the lights first and remove the fog light bezel similar to these covers. Not much different.

Now we are up to the headlight brackets. These brackets are secured with three rivets and the only way to remove them is by drilling the rivet out. Make sure your drill bit is not too big and do not hurt yourself. When it comes to the installation of the rivets, you will most likely be using a handheld rivet gun or riveter. These can be purchased at any hardware store with various sized rivets. We used our old pneumatic gun. The bracket lines up with the larger notch on the inside of the bumper Be sure to line up the three holes correctly. You want to first insert the rivet into the riveter or rivet gun. Treat like the shot of a pistol or an injection shot. Carefully place it in the desired area apply pressure to the trigger. Repeat on both sides.

Hopefully, you have not forgotten how to take off the accessories because now you just work in reveres to install them. Start with the top grille and make sure that the bumper tab slides in between the grille. The rest should be pretty self-explanatory. Just make sure all the tabs are sitting within the grilles before you Hulk smash them in. It’s that easy folks!

Source: https://www.revemoto.com

Follow Us on
FB: https://www.facebook.com/ReveMoto/
IG: https://www.instagram.com/revemoto/
Twitter: https://twitter.com/revemoto?lang=en

________________________________________________________
#HyundaiVeloster #revemoto #paintedautoparts #Veloster #highquality #DIY #HowTo

DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness, or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.