Great and helpful video. I have a similar problem…Honda HRB215, serial
MZBA-6405287. The blades spin and engage just fine when I put the lever in,
cable is tight as well. When I go to cut the grass, the blades basically
cut for a few feet then stop spinning. If I were to replace the disk/clutch
lining part as you did in your video, should this solve my problem? Do you
happen to know the part number I need for my mower, or where I can find the
part #? Thanks in advance!
my Honda mower vibrates a lot when off clutch… could be wrong blade? when
the mower clutch is activated and mowing, the mower hardly ever vibrates
and runs very smooth…
I have a Honda HRB216HXA and looks just like what you are working on, Very
good and simple information but I do have one question, When I try to take
the bolt off the belt rotates and I can’t seem to be able to unsrew the
bolt. Any ideas? Oh an do you hapen to know the part number for the
HRB216HXA? Thanks for any help you can give and the video.
Undo the engine cover and stop the flywheel turning with a strap or wedging
it so it does not move. In this video he has an impact tool to undo the
bolt. Good luck.
Great vid thanks. I have an old mountfield M3 with roto stop the brake
works but the mower wont cut under load the blade spins under momentum but
has no drive? Id really appreciate any help ? Thanks for posting. Stampy
Good vid. What was wrong with the clutch you removed? Was there visible
damage? Thanks.
Great and helpful video. I have a similar problem…Honda HRB215, serial
MZBA-6405287. The blades spin and engage just fine when I put the lever in,
cable is tight as well. When I go to cut the grass, the blades basically
cut for a few feet then stop spinning. If I were to replace the disk/clutch
lining part as you did in your video, should this solve my problem? Do you
happen to know the part number I need for my mower, or where I can find the
part #? Thanks in advance!
it was a worn out clute disk plate right? is this the same for honda
hrc216hxa’s? they have a differnt blade clutch set up
my Honda mower vibrates a lot when off clutch… could be wrong blade? when
the mower clutch is activated and mowing, the mower hardly ever vibrates
and runs very smooth…
Was that an oem part? can you get an aftermarket plate like that?
Man, I am glad to see your videos again.
Good to see more videos, another good one. Take care.
yes the part # is 75150-VE1-R00
Nice and quick, ebay is sometime dam handy as long as you dont buy parts
from china as the copys can be a bit too cheap.
I have a Honda HRB216HXA and looks just like what you are working on, Very
good and simple information but I do have one question, When I try to take
the bolt off the belt rotates and I can’t seem to be able to unsrew the
bolt. Any ideas? Oh an do you hapen to know the part number for the
HRB216HXA? Thanks for any help you can give and the video.
Thank You, Thank You. . . . Rock On Keep Your RAVING Fans HAPPY WORD IT
AROUND FAST THAT YOU THE MAN! !
Good to see you posting videos again. Do you check the torque with a torque
wrench when refitting blades for safety?
Undo the engine cover and stop the flywheel turning with a strap or wedging
it so it does not move. In this video he has an impact tool to undo the
bolt. Good luck.
it was worn out
Great Vid MM1. Sure looks a lot easier than the older Lawnboy BBC. I wont
even take the lawnboys anymore that have those clutches…
Great vid thanks. I have an old mountfield M3 with roto stop the brake
works but the mower wont cut under load the blade spins under momentum but
has no drive? Id really appreciate any help ? Thanks for posting. Stampy
thanks! im back in the groove!