http://www.1aauto.com/1A/IgnitionSwitch/Ford/Ranger/1AZIS00008 1A Auto shows you how to repair, install, fix, change or replace a damaged, worn out, faulty o…
http://www.1aauto.com/1A/IgnitionSwitch/Ford/Ranger/1AZIS00008 1A Auto shows you how to repair, install, fix, change or replace a damaged, worn out, faulty o…
You must be logged in to post a comment.
Nicely done video. Appreciated the tool list, made my repair short and
sweet this morning.
We currently do not have an auto repair video that shows this particular
repair. 1aauto.com 888-844-3393
what about a 1994 ford ranger, I took off both panels, but can’t locate
ignition switch
There is not. You need the rod to push out for it to start.
You may have to trace the wiring to see if there’s a wire touching a piece
of metal somewhere or that could be possibly corroded causing it to short
out.
Do y’all have a video on how to replace ignition lock
For the 1993 it might be similar. Unfortunately we do not have that model
year around to check it out so it might require you to remove the steering
wheel so you can pull it out.
The switch is going to be located right behind the key cylinder.
how do you replace a ignition switch on a 1998 grand marquis
We currently do not have an auto repair video that shows this on your
particular application. Some of the basics may be the same as shown in this
video. We do carry a replacement ignition switch for your 1998 Grand
Marquis. they are available on our website 1aauto.com Part# 1AZIS00008 or
call sales 888-844-3393
I am bypassing my ignition switch in my 1995 Mazda B4000. Because the
plastic rod inside my steering column broke and I can’t shut it down
without pulling the fuse. My question is, on my switch, which wire is
which. Google is no help.
It may be worn out.
I have a 1995 Ford Victoria Police Interceptor. I believe the Ignition
Actuator Rod needs replaced. I have replaced the Ignition Switch, Ignition
Lock Cylinder and the Ignition Relay Switch. My question is, is there a way
to bypass the Actuator Rod and get the car to crank? Thanks!
@1aauto thanks i already replaced it. this video was helpful it was just a
little different i had to drop the steering wheel but it was still quick
and easy repair ,thanks again this video gave me the confidence to do it my
self
If you have a service manual for the vehicle, there should be a wire
schematic in there for you. 1aauto.com 888-844-3393
The ignition switch on your application should be different. We currently
do not carry one for your vehicle on our website. 1aauto.com 888-844-3393
wheres the video on how to put an ignition switch on a 1988 ford ltd crown
victoria
I have a question. I have a 1988 Mercury Grand Marquis 5.0L FI 8cyl the
problem is that i had to disconnect the battery because the starter will
start with out me putting the key in and i been having this problem for
months and kant find the problem for it and i really need to fix it but
don’t know what could be the problem. Can u please help me 1aauto?
We do have this one, that shows you how to replace the key lock switch on a
90-96 Ford Ranger. youtube.com/watch?v=PWGrv0hba08&feature=plcp
Can you guys tell me if this is close to the same set up for a 1998 Ford
Explorer XLT model ? If so, I can do this myself and save alot of money.
how do you replace the ignition switch connector(re-wire and replace) on a
1994 crown victoria
Hi , would replacing this switch maybe help a problem I have where the
radio/clock stays on even when the key is removed sometimes.
How do you know if your switch is bad i have a 2002 ford ranger 2.3 4 cyl
and it will start fine but ever once and a wile it woint start at all and
if you wiggle the switch a little bit it will start i put a brand new
battery on. Thanks
hello i have a 95 ford explorer is this the same switch for it as well
is that the same thing as a ignition module?
Is the ignition switch on a 2006 Ford Ranger in the same location?
Yes this is the same switch that is used on the 1998 Ford Explorer. We
carry them on our website 1aauto.com 888-844-3393 Part Number: 1AZIS00008
@dpl1108121 We’ll keep this in mind if we need to make this repair in the
future. They usually aren’t to hard to fix. A Haynes or Chiltons manual
should show you how to make this repair and where it’s located on your
vehicle. We sell the Haynes manuals on our website 1aauto.com
is the ignition switch on a 93 ford ranger in the same place? Does it have
a cover over it as well? Do you by chance have a picture?
It sounds like something in the switch may be worn or loose, which could
cause the vehicle not to start until you wiggle the part and those pieces
make contact again.
There could be a draw or an issue with the radio itself too. You may want
to look at it.
Is it pretty much the same as the ford ranger
This video will show you how to replace the switch (not rewire) but replace
it. 1aauto.com/1A/IgnitionSwitch/Ford/CrownVictoria/1AZIS00008/486013/1994
I have an 96 madza b2300. i pulled the key out of the ignition an the
steering wheel did not lock and the engine did not shut off. would
replacing the ignition switch be my solution?
i replaced the starter switch bought a new battery and it still woint start
it will start 90 percent of the time but when it woint start all you got 2
do is hit the steering coluim and it will start right up i took it to a
lock smith and he said it could be a bad antenna he made me a brand new
transponder key
@TheMcfooly Can’t remember doing one on a 91 Explorer but I would not be
surprised if it was a very similar process.
@dpl1108121 This is the ignition switch. The ignition module should be
located on or around the distributor.
thanks for your help im going to try this then and ill tell you if it worked
It sounds like there could possibly a frayed wire in the column. If the
truck starts when you hit the column, there could be a loose or frayed wire
in there.
@MrDuccimane We currently do not have an auto repair video on that
particular repair for that vehicle. A Chiltons or a Haynes manual should
also show you how to remove it. We sell the Haynes manuals on our website.
Here’s a link to them. Hope this helps you out.
1aauto.com/1A/repairmanual/Ford/CrownVictoria/1AMNL00064/219998/1988?utm_source=youtube&utm_medium=youtube&utm_campaign=1ATony
is a 1991 ford explorer the same
@1aauto if you could do a video on where that is located on the ranger!
That would help me out big time.. also is it hard to fix that?