I have a 2000 Dodge Avenger and it does nothing when I put it in reverse.
You can feel it bump when you shift it in reverse but you don’t move
anywhere. I can floor it and still won’t move anywhere. Any help?
Hello rich I have a Plymouth neon year 2000 engine 2.0 liter 16v sohc. My
engine check light is on. The performed diag to dtc po743 ttc solinoid
circuit. Checked proper operation advised of vlavle body replacement/ ttc
solinoid. The shop want 1200 to fix but couldn’t due to the new vlavle body
has been discontinued for my car. What should I do ?????
I think before I would have tackled that job the first thing I would have
done is steam cleaned that shit hole of an engine and engine bay out, just
a couple of grains of muck would have knackered the whole box up, plus if
it had been cleaned in the first place you would have seen where the leak
was straight away before wasting time and money doing an unnecessary gasket
job.
my pcm suffered an injury in a crash for this reason my transmission does
not operate properly remove the computer for repair and now i install the
computer again and anti theft mode is activated red circle in my panel. i
disconnect the terminal of the battery for a period of 24 hours and leave
the key on for 20 minutes and the problem is the same the car don’t start
don’t make any noise anything have any idea how to fix this? btw i live in
Panama (latin america) the dodge don’t have a dealer in my home town i buy
this dodge neon in coopart :(
i replace the transmission solenoid, speed sensors and transmission fluid
with filter and have same problem my transmission is stuck in 2nd gear
(dodge neon sxt 2004) in the process i disconnect the battery is possible
that i need to reset the PCM and TCM with a Diagnostic Scan Tool to remove
the limp mode on the transmission?
I have a 1999 Dodge Grand Caravan with a 3.8 V6 engine. It shifts really
hard when I put it in Drive from Reverse and I believe it is being stuck in
1st or 2nd because it seems like it won’t shift at all. It stays between
2-3,000 RPM’s and won’t shift after 2nd. My husband said he doesn’t believe
it’s shifting out of 1st but it does for me. Any suggestions? Also, how do
you unplug the Torque Converter Plug? Thanks
I recently changed a Dodge Caravan transmission and one of the connectors
had a square pins instead of rounds pins have you ever heard of that ?and
how do I address ?it is there an adapter for the connector
I have a 03 neon and I out it in drive and its good for like half a block
then it stops going I accelerate and the rpm goes up and it’s on drive it’s
as if u put it on nutral wen ur steal in drive can u help??
one thing that makes it easier is to remove the cooler hoses to get to that
center bolt with a swivel or wobble extension, also on some 41te
transmossions on older vehicles there is a service bulliten that has to do
with tapping the case behind the solonoid due to the metal of the case
being too porous
Hello i have a problem i have a Town & Country 2004 and the gears do not
change my mechanic changed the transmission and once again it does not
change gears he put 2 transmissions in already he checked my computer and
it turns out thats still good to i dont know the problem what else does he
need to check so he can fix the problem. What do you think ?
What codes r U getting? turn key forward3x’s w/o starting. leave forward on
3rd give u dash codes. had same prob w/ P300 random misfire. Battery was
bad + bad O2 sensor. Bad solenoid/ trans probs are usually in the P750
range.
I have a 2000 Dodge Avenger and it does nothing when I put it in reverse.
You can feel it bump when you shift it in reverse but you don’t move
anywhere. I can floor it and still won’t move anywhere. Any help?
Hello rich I have a Plymouth neon year 2000 engine 2.0 liter 16v sohc. My
engine check light is on. The performed diag to dtc po743 ttc solinoid
circuit. Checked proper operation advised of vlavle body replacement/ ttc
solinoid. The shop want 1200 to fix but couldn’t due to the new vlavle body
has been discontinued for my car. What should I do ?????
my 2004 Dodge Neon is making a growling noise when I drive forward its
driving me crazy.
hi rich mi car is toyota camry it have code P0773
I think before I would have tackled that job the first thing I would have
done is steam cleaned that shit hole of an engine and engine bay out, just
a couple of grains of muck would have knackered the whole box up, plus if
it had been cleaned in the first place you would have seen where the leak
was straight away before wasting time and money doing an unnecessary gasket
job.
Hi, why not only changing the Gaskets if there is a link coming from TCS?
I have a 03 Dodge Ram 1500 Quad cab with trany prob no dr & overdr the
codes that come up are p0700/po703? HELP PLS
Great video. Very helpful. Would a bad TC Solenoid cause a car to stall
when it’s placed from park into drive or reverse?
Thanks HEAPS
Great video, it worked!!
Transmission control module him
my pcm suffered an injury in a crash for this reason my transmission does
not operate properly remove the computer for repair and now i install the
computer again and anti theft mode is activated red circle in my panel. i
disconnect the terminal of the battery for a period of 24 hours and leave
the key on for 20 minutes and the problem is the same the car don’t start
don’t make any noise anything have any idea how to fix this? btw i live in
Panama (latin america) the dodge don’t have a dealer in my home town i buy
this dodge neon in coopart :(
what about a 04 chevy impala 4t65e transmission same process?
i replace the transmission solenoid, speed sensors and transmission fluid
with filter and have same problem my transmission is stuck in 2nd gear
(dodge neon sxt 2004) in the process i disconnect the battery is possible
that i need to reset the PCM and TCM with a Diagnostic Scan Tool to remove
the limp mode on the transmission?
I have a 1999 Dodge Grand Caravan with a 3.8 V6 engine. It shifts really
hard when I put it in Drive from Reverse and I believe it is being stuck in
1st or 2nd because it seems like it won’t shift at all. It stays between
2-3,000 RPM’s and won’t shift after 2nd. My husband said he doesn’t believe
it’s shifting out of 1st but it does for me. Any suggestions? Also, how do
you unplug the Torque Converter Plug? Thanks
I recently changed a Dodge Caravan transmission and one of the connectors
had a square pins instead of rounds pins have you ever heard of that ?and
how do I address ?it is there an adapter for the connector
hi i have a hard shifting trans 2005 corolla 277k now with
p2716 code on trans oil is clean havent change trans oil
43k should i change it?
i need to drain the transmission fluid to change the solenoid?
I have a 03 neon and I out it in drive and its good for like half a block
then it stops going I accelerate and the rpm goes up and it’s on drive it’s
as if u put it on nutral wen ur steal in drive can u help??
one thing that makes it easier is to remove the cooler hoses to get to that
center bolt with a swivel or wobble extension, also on some 41te
transmossions on older vehicles there is a service bulliten that has to do
with tapping the case behind the solonoid due to the metal of the case
being too porous
Similar what acura tL has
Hello i have a problem i have a Town & Country 2004 and the gears do not
change my mechanic changed the transmission and once again it does not
change gears he put 2 transmissions in already he checked my computer and
it turns out thats still good to i dont know the problem what else does he
need to check so he can fix the problem. What do you think ?
On this neon after the install there was nothing else that had to be done.
What codes r U getting? turn key forward3x’s w/o starting. leave forward on
3rd give u dash codes. had same prob w/ P300 random misfire. Battery was
bad + bad O2 sensor. Bad solenoid/ trans probs are usually in the P750
range.
Thank you so much for all this information. What would your next move have
been if there were still a leak?
@Filmaker25 very little.
My dodge (grand caravan) is leaking transmission fluid 🙁
when changing the solenoid do I also have to replace the output and input
sensors? Please and Thank you this video us very helpful and saved me money!