i’m repairing the box sides on my ’03 Silverado soon, nowhere near what they were. a lot of rust bubbles in mine, just over the wheel wells. my truck is going in the body shop for an insurance door, they looked at the box, I told them I was putting flares on after I fixed it, they said cut a hole about 8 inches long and an inch high, clean it out, sand, prime, rock guard, then flare, not to fill in the hole if its being covered.
Are you using rattle cans for the primer or a two stage? I am trying to do a van that has to stay outdoors and I can only do a little at a time and need to prime between steps to keep new rust down. Any product suggestions?
Hey Pisser, I have a 02 Duramax. Love the truck but both rockers and driver side cab corner need to be replaced. Will i have to do both inners and outer rocker panels ? Shops around here say as long as there is enough metal to weld to i would be ok. How long is the repair you did to the truck going to last ? Tough to find a good shop in RI to trust to work on my favorite truck
Just had some arch repair panels done exactly like this on a mk1 golf I’m restoring. Guy made a really bad job and although I could prob fill it I’d rather take them off and get them done properly. Any advice on getting them off after they’ve been welded without damaging the existing panel below?
){kind=link}
body lines aren’t critical i suppose.
i’m repairing the box sides on my ’03 Silverado soon, nowhere near what they were. a lot of rust bubbles in mine, just over the wheel wells. my truck is going in the body shop for an insurance door, they looked at the box, I told them I was putting flares on after I fixed it, they said cut a hole about 8 inches long and an inch high, clean it out, sand, prime, rock guard, then flare, not to fill in the hole if its being covered.
Are you using rattle cans for the primer or a two stage? I am trying to do a van that has to stay outdoors and I can only do a little at a time and need to prime between steps to keep new rust down. Any product suggestions?
who the fuck clear coats over a bloody sticker? idiots. Anyways, nice work man.
Thanks for the vid!
Its the guy from the brave little toaster
on ebay u can get those 4×4 stickers for 12 buck and u can get way sicker one screw the dealership
complete shit, they use tin tape in stead of a panel or makeing a panel and weld it, they put the tin tape on and then bondo the shit out of it.
Hey Pisser, I have a 02 Duramax. Love the truck but both rockers and driver side cab corner need to be replaced. Will i have to do both inners and outer rocker panels ? Shops around here say as long as there is enough metal to weld to i would be ok. How long is the repair you did to the truck going to last ? Tough to find a good shop in RI to trust to work on my favorite truck
Chooching= Getn high
Are you ever going to do some vids on the mustangs?
Just had some arch repair panels done exactly like this on a mk1 golf I’m restoring. Guy made a really bad job and although I could prob fill it I’d rather take them off and get them done properly. Any advice on getting them off after they’ve been welded without damaging the existing panel below?
pisser you need to upload the ultimate hack n’ pack silverado,
When I see pisser rust repair vids, I feel like such a pussy for bitching about a 4 inch rust through I’m trying to patch on my VW bug….
True that!
lol,ya get what ya pay for..
Hey pisser! Is Maco any good??
Vintaaage! 😀
Rustang!
What a difference 🙂
shawn wat did u do with ur mustang and vw
Ah vintage pisser 🙂
I like that you don’t over dub your audio. Makes for a more personal feel.
Thanks for the video Pisser. I’m assuming that this video was shot much ealrlier since you’re not up to your ass in snow. Good job Bud!
whoa audio went crazy around 8 minutes
I remember these old video’s. Good stuff.