http://www.1aauto.com/1A/BrakePadAndRotorKits/Chevy/Impala/1ABFS00003 1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky…
http://www.1aauto.com/1A/BrakePadAndRotorKits/Chevy/Impala/1ABFS00003 1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky…
You must be logged in to post a comment.
Thanks for watching. 1aauto.com 888-844-3393
Mike is the beezneez. Old skool cat with swagger. Man you saved me a bunch and it wasn’t hard to do at all. Beer and wings on me!!! All in all greats stuff and thanks on behalf of all d.i.y. guys and gals.
Yes the will seem loose because they kind of float on the hubs until everything is put back on and the brake calipers are pumped back up.
I have a question, When you have the calipers off and the brake assembly- on this particular model of car will there be any play left or righ witht he rotors as they sit on the studs…Mine move quite a bit- I would assume they would
Appreciate the help !!
THANK YOU 1AAUTO!
Me and my boyfriend had a fight and then he wouldn’t do my brakes. This video walked me right threw it. I’m 5’2″ and 115 pounds but i was ratcheting my tires off and throwing them under my car. I had my brakes done in an hour!
You do not need to unless for some reason the brake pedal becomes very hard or soft after the brake job. Hope this helps you out, have a great day. 1aauto.com 888-844-3393
4:12 looks like a new wheel bearing too.
Usually what you can do is leave the old brake pad on, and use the old pad to collapse the two calipers together with a C-Clamp. Hope this helps you out. 1aauto.com 888-844-3393
Thank you for this video. I just replaced my front brake pads and rotors on a 2009 Chevrolet Impala LS 3.5 liter. I noticed I had two pistions per caliper. I pushed back each piston separately – was that the correct procedure??? Also, each rotor was held to the hub by a torx screw (I couldn’t figure out at first why the rotor would not come lose). Basically the overall procedure was the same. I pumped the brakes, took it for a test drive, and all is well. Thanks again! No more pulsating!
We currently do not have an auto repair video for this particular application. We’ll keep this in mind when making repairs in the future.
Can you help me?
How to replace the spark plugs for nissan armada 2004
Thank you.
Thank you for all of these videos that you’ve posted. I’ve gained a great deal of knowledge about mine and many other vehicles simply from watching your thorough explanations.
We carry brake pad and rotor kits on our website for your 2001 Chevy Impala. Here’s a link to them on our site. All of our parts include FREE SHIPPING in the lower 48 states. 1aauto.com/1A/BrakePadAndRotorKits/Chevy/Impala/-/-/2001?utm_source=youtube&utm_medium=youtube&utm_campaign=1ATony
What kind of rotors and brake pads would you reccomend??? I have an 01 Imapal. Thank you.
It could be that the fuel filter needs to be replaced, or possibly injectors that need to be cleaned.
They may be similar. On some vehicles you need to turn the caliper in using a special tool that fits into a couple of holes on the backside of the caliper (not sure if this is set up that way). If they’re not, you would be able to collapse them just like the front ones.
Awesome Video! It was clearly explained and demonstrated. I do have 1) question, I need to replace the rear disc breaks on my 2003 impala. Are the same basic steps and principals involved in replacing the rear disc breaks as the front disc breaks? Thanks again for this video.
I have a 2003 Impala LS 3800 and when I start up the car it doesn’t start if its been sitting. Usually at those times I have to give it gas by pressing the gas pedal lightly rev the engine to get it to stay on. What could this problem be?
Thank you for stopping by and checking out our auto repair videos.
Great vid, very nicely done. Noticed it while looking up a “Plan B” for a stripped bleeder bolt on a front caliper for a 2002 Impala. Will go hunt to see if you have a caliper rebuild tutorial.
All:
Thanks to Mike Green at 1A Auto , I can’t tell you how much this 2000-20005 front brake job on my impala, simple, helpful and efficient.
Thanks again!
Paul
does the cal pin with the rubber at the end go on top?
Just got to 1A Auto dot com and in the search box type ‘magnetic tray’
How can I get one those 1aauto magnetic plates? I’m always losing bolts when I do a repair. Btw, you videos are awesome!