In this video I show you how to replace you valve cover on an N54 motor.
I’m working on my 2008 BMW E90 335i.
I also show you how to replace the o-rings in your blow by PCV vent tube which goes from your valve cover to your rear inlet.
You should set aside a couple hours to preform this job.
You had a timing chain replacement video for N54 but it's gone? I learned how to diy
my N53 from scratch by watching your videos, never fixed a car before.
Now I basically just top up the screen wash ;)..
Started with spark plugs, ended up on valve cover to make long story short. First time with sp's felt like a miracle.
So I would reeaally like to see that video…. Regards!
Quick question is draining oil before attempting my this necessary? Will it make a difference in mess or no
I set my torque wrench to exactly 78 inch lbs which is equal to 6.5 ft lbs and the first bolt broke off…idk why
My car smokes every morning when I start driving for a few minutes you thinks is that gasket ?? Its embarrassing because it looks so nice
Ahh…doing my first n54 rebuild and not having to do any REINZ sealant on those blasted "half moons" is a dream come true. Great video.
What happens if I disconnected the positive ground but didn’t disconnect the battery I’m having water pump problems now please help
Question: I have a 2009 535i and have completed all steps per your video, but having a hard time lifting the head. The intake side lift a bit but the exhaust side seem to be stuck. I feel something else is holding it down like a bolt or so. I have loosened all the e10s and the three studs but have not removed them completely, do you think that is the problem? Thank you very much!
Thank you! With this video, I finished mine today.
CONGRATULATIONS once more for the job and show us how to mantein our machines on this critical but afordable manitenance as shown for a DIYer owner of a BMW. Torque and order is very important to replace the cover again aswell. This is an issue for every BMW after 100.00 kms. more or less also with oil filter gaskets both block and cooler.
Just to know which kind of cleaner or degreaser do you use to keep the engine bay nice and clean as it could be found in a BMW official concesionar.
thank`s alot from Europe
BimmerN53
Im praying mine is as pretty as this
Like your videos out of Toronto Canada I have a 2012 BMW X3 m f25 burning oil can help me please thanks
Why would anyone downvote this video?? I just found out my valve cover is cracked and I’m only at 59k miles. So I’ll be doing this soon. It’s nice you don’t have to removed the injectors. I was worried I was going to have to.
If the valve cover is bad should you see oil in the spark plugs???
I think you should’ve remove the fuse for the fuel then turn the ignition to release the pressure from the line then unplug the battery
Oh man, this is increadibly helpful. Got my valve cover gasket but it's been in my boot for 3 months now as I had no confidence. I am off to start. Thank you!
Just tackled this with my son! Thanks for the great video. I left the fuel lines attached to the main rail, and I removed the vacuum can with the 13mm nut to give me access to the lines. Everything else was pretty easy. Only issue I had was snapping off a bolt on the wiring harness. No biggie.
Keep up the great work!
Changing the valve cover gasket on my E39 with the M54 engine. Bought OEM gasket kit. Do I need any type of silicone or something before I put my gasket on?
Man I want to thank you for all your videos I’m finally doing my valve gasket on my 08 E90 335i and been watching every step of your video to help get the job done keep up the good work. Btw can’t wait to see how the HPFP works out on your new turbo Mo Powa Baby lol
What is fantasic video. Just saved me about €900. Thanks a lot.
Charles Bukkens. The Netherlands.
I keep coming back on this video when my 85 thousand mile N54 gets me discouraged. I have to do my valve cover and love this video thank you. I hope mine lasts just as long as yours.
lol Brake Cleaner on plastic and rubber orings…..
Pull the fuse to the pump and start the car, run it until it stalls and then remove the fuel rail.
Thanks doing my this weekend.
Fuck this shitty gasket, I been trying to put the valve cover back in for the past 2 hours and every time the gasket sags down a little and gets caught on injector 6