First: I do not take any responsibility (failure of your car, car brakes, accidents). I do not sell any DVDs or instructions. This is Bosch motronic 5.3 ABS …
First: I do not take any responsibility (failure of your car, car brakes, accidents). I do not sell any DVDs or instructions. This is Bosch motronic 5.3 ABS …
You must be logged in to post a comment.
){kind=link}
when i touch with the solder i burn 3 – 4 wires around ,,,
why…
What kind of problem did you repair? What was the error in VAG COM ???????
How much do you charge to fix the abs module?? i have a bosch 5.7
I did this on my Audi A4 B5 and the three beeps and flashing brake light is
gone! The ABS light is stil on. Will the ABS work now, or do I need to
clear any fault codes first?
Nån som vet om det skulle va lika lät att göra det på en e90.Nån som har
gjort på en sånt eller nåt liknande.Bor i örebro trakten nån som tror kan
ficksa det få höra av.Klart ska ni få betalt.Mvh
I have the same problem and am about to send it off to the guy in FL who
will repair it for $99. But i’m curious why this circuit looks so weird,
looks like a circuit board from the 70s, and it’s covered in some goo
right, what was audi thinking??
Hello, for the Alu wires, can they be soldered with normal Iron ?
dsfsfsd
Hringdu bara í mig. Er á Já.is
Albans a bit like I would say in my country but effective
Vet ej varför det blev fel stavat? men hoppas ni förstår vad jag menar.
HI THIS IS PAOLO FROM DEA AUTO. . AFTER SEEING YOUR VIDEO I WAS VERY
ENTHUSIASTIC OF WHAT YOU CAN DO, SO I WOULD LIKE TO LEARN SOMETHING MORE
FROM YOU ABOUT THE REPAIRING OF ABS. DO YOU HAVE SOME INSTRUCTIVE MATERIALS
TO SELL ME LIKE DVD, OR MANUAL ABOUT HOW REPAIR THE ABS. AND DO YOU HAVE
SOME SKYPE CONTACT OR A TELEPHONE NUMBER WHERE WE CAN TALK ABOUT THIS. MY
SKYPE CONTACT IS ideacar1 OR YOU CAN SEND ME AN-MAIL TO deauto@hotmail.it.
THANKS A LOT. BEST REGARDS
Sæll Arnar, ég á við sama skemmtilega vandamál að stríða. Tókst þér að lóða
þetta sjálfum eða fékkstu einhvern hæfan lóðara á klakanum með fínlegar
græjur til að aðstoða þig? Með fyrirfram þökk og kveðjum.
Thank you so much for this video!! I had exactly this problem in my module
and I had never been able to fix it by myself without this video.
@MrElvey (continuing) From what I read here, it sounds like my module
probably has this problem. I can’t actually see what you’re doing in the
video. Are you basically replacing two aluminum wires with two gold wires?
(And somehow not shorting anything out – it looks like it’s a rather
difficult solder job.) ANYONE near Oakland CA willing to work on this for
me?
I received opened module. Do not use dremel. Do it by stanley knife or
scalpel. Do it gently and carefully. Cut the gray silicone around cover.
Finally, close with a waterproof silicone or glue, but first test if works.
Sæll Arnar, ég er með 1999 módelið af A6 sem að næst ekki samband við ABS
tölvuna í. Var það e-ð viðlíka vandamál sem að þú lagaðir í þínum bíl?
Just finished doing this to mySaab 9-5 aero hot and it worked a treat
thanks for the post you are a saviour 🙂
You can solder aluminium under motor oil (prevents oxidation). Module works
now over a year, without any problems. And if module breaks again you will
se a red light or error message on dashboard… I don’t see any problems
here.. if you drive with red light on dashboard.. your problem 😉
Where can i buy this Acid Stearinicum please? Any place or website? Thank
you.
hi what did you use to remove the gel covering the board
1998 A4 with just 2400 franks to fix this module? Save the 2400 and sell
your car, get a new one that has the working module. Here’s a fix for you.
I don’t know.. I don’t own VW, but if module is like this in video it is
90% this error. In this month I repaired third one (Audi 98 and 2x VW
Passat 99) – same error – aluminum wires. You can take a photo of module
(on the right side of the car hood) and send me. I will try to recognize a
module if is like this one.
A friend accessed the net and YouTube and your video and asked me to write:
“Thanks — your fix worked for my ’90 Passat. Only problem was I wasn’t
used to such fine soldering and broke one of the very fine speed sensor
wires. Nevertheless, allowed car to pass inspection.”
Heb type bosch 0 273 004 284 opgemaakt met stanley mes, eerst even goed
inkrassen en dan snijden, twijvelde over de draadjes maar na opene zaten ze
echt los! heb net 2 bier gehad dus ga ik dat vandaag niet solderen, zoek
morgen flux op en silvertin met mijn boutje en ga het proberen te sloderen,
al het lukt zet ik het op de tube
are they both on the same pin?
Thank you very much for this video, I had the same problem. ABS working
again!
So it is just as simple as you showed us. Just connecting the wire again
and it should work. But what about “acid stearinicum” what is it for?
hello friend… i am trying to do same but with another computer. i have a
problem which is the wire can not be sold with the terminal, i am thinking
could be the temperature i am using for, but i am not sure… i bought the
same acid, but maybe i am using a wrong solder (ALUSOL MULTICOR). may you
help me?? i apreciate your answer/… kind regards.
@jvolk0 I totally agree with your reply to @diagnet ! I have a 2000 VW New
Beetle 1.8T and the ABS ECU (I THINK it’s part 1J0 698 417A 98-09, or at
least that’s a valid replacement) is malfunctioning (the codes I get are
that 3 of the ABS speed sensors are intermittently failing, and the two
lights typically turn on when I hit a bump, and go off a while later.) My
mechanic says that he can’t replace the module with a used one off ebay; he
can program a new one but not reprogram used.