http://www.AndysAutoSport.com/coilovers.html 1 (800) 419-1152 Andy’s Auto Sport shows you the general steps involved in installing a set of coilovers in a ty…
http://www.AndysAutoSport.com/coilovers.html 1 (800) 419-1152 Andy’s Auto Sport shows you the general steps involved in installing a set of coilovers in a ty…
You must be logged in to post a comment.
){kind=link}
No alignment?
If you love cars, don’t forget to subscribe :)
Do you have any coilovers that directly bolt up to a Nissan 300zx (Z31)?
well, i have a 2008 rt dodge charger, do i have to change my shocks?
2003 Mitsubishi Outlander LS AWD. Stock clearance height is 8.3″. Anyway to
increase it by half inch at least? I’ve ask the tire/rim shop people and
they said my vehicle only has 1 tire and rim size available after looking
it up in their book.
oh ok. Is there a way to increase the ground clearance of a vehicle by
changing to a longer strut?
yeah but slightly larger tire weren’t an option for me since they said…
my vehicle is only available for P225/60R16
If your truck physically has the room for them, the tire size should be
your choice. a 225/65R16 would probably fit just fine as long as there is
nothing in the way.
Most common coilover setups are designed for a lower ride height, unless
otherwise stated by the manufacturer.
There is, but without knowing what type of vehicle it is, we can’t be very
specific.
You could likely fit slightly larger tires on it, which would give you the
extra half inch you want. There aren’t really any lift options unless you
fabricated your own strut spacers.
Kudos to AndysAutoSportTV for actually responding to peoples questions.
When I have money for it I’m going to do a lot of these mods on my Lancer.
Really helpful. Ordered coilovers for my VW Golf mk3 and wanted to see how
difficult it would be to install them. If its anything like this car it
should not be such a problem. THANKS 😀
oh okay, thanks for the advice. I will measure the distance between the
tire tread and the wheel arch to make sure.
What we typically refer to as a strut is an assembly consisting of a strut
casing and shock absorber. Thanks for watching!
If they rub during suspension travel or turning, then yes. Thanks for
watching!
The parts above the tires on that gen Accord are the spindles/uprights and
the upper control arm. They move up and down with the wheel during
suspension travel, so no need to move them. Thanks for watching!
I’m wanting to increase the ground clearance on my vehicle, is it possible
to increase it by getting the coilovers? Btw, it’s not a sedan it’s a
unibody crossovers SUV
We always suggest an alignment after lowering or lifting a vehicle. Some
are worse than others, but they’re always at least a little bit off after
any suspension changes. Thanks for watching!
I know shock absorber and damper are the same thing, what about strut? Is
strut a shock absorber/damper?
WALTER WHITE? ITS THAT YOU?
What Tein coilover suspension is that & i noticed you didnt install any
camber kit. Is it needed with installation of any coilover suspension?
seems easy, thanks for the video!
So i have a question. I have a 1989 honda accord i want to slam but, about
the tires is a weird bracket. can i move this bracket or what?
hey, i want to slam my car, you know wheel arches over the tyre a bit, do i
need to remove my wheel wells to do so?
Thanks, i’ll have to save this for use later;)
Do you need to change stock struts if you put adjustable coilovers? and do
you need alignment? Any advice is appreciated.
do a video of how to adjust tein coilover..
did you need an alignment afterwards?
Would have been much easier if you had unbolted the stabilizer link.
This is going to help me next week when I install my suspension in my
Integra
We have one in the works. Please subscribe so that you’ll be notified of
all future video releases. Thanks!
have you guys done a video on how to install adjustable coilovers?
What the part number for the coilovers used in that integra
i love Mechanix Gloves 🙂 you guys should do a glove review for track
gloves and mechanical gloves. excellent seat videos, by the way. im
bookmarking them for later 😉 excellent choice in rims and tires, too.
You should do a project on a Mazda 6 3.0L
mike birbiglia