Brian Eslick from How to Automotive http://www.howtoautomotive.com takes you step-by-step through the process of replacing the crank sensor on a 2001 Mercedes C240.
Affiliate link mentioned in the video for Crank Sensor http://amzn.to/2fEAfB4
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: http://www.howtoautomotive.com/
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: https://www.facebook.com/How-to-Automotive-432536836946801/?ref=settings
Google+: https://plus.google.com/+HowtoAutomotive/posts
LinkedIn: https://www.linkedin.com/in/brian-eslick-819839118
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive
Bro be honest you didn’t get it out like that did you? I’ve tried everything and it doesn’t work like this. I’m this close to taking the whole engine out because I don’t see any other way to loosen the sensor
Why was the part replaced ?
Get the car up and do this from the bottom, way much easier.
My friend, can you explain a little more about what was your car doing, did you have fuel pressure, did the engine chranck but didn't start? Thank you buddy
My car starts but if I turn it off after I go to lets say… the market or getting gas, it doesn't turn on, it just keep cranking it won't turn over, could this sensor be y?
Great presentation. keep it going
Great video thanks for the helpful tips. This job was a real PAIN IN THE ASS. I have large hands so it was very hard. My right hand and wrist is so sore now lol. I tried a variation of extensions, tried the universal joint in different spots, used tape to hold the angle of the socket because the darn bolt is blocked by the senor. I dropped the bolt a few times and had to fish it out. But she did start after completing the job and I let her run a few minutes and she didn't shut off. I cleaned my MAF sensor while I was at it and tomorrow I will clean the elbow and the throttle body, along with replacing the air filters and I will drive her after that. Fingers crossed after the engine comes up to temp she will not shut off.
My 01 c240 stopped running on the frwy, felt it loose power as I give it gas, got it towed. After getting it home I would start it but it would only idle until I give it gas then it would shut off. No check engine light, what could cause this ?
Thank you so very much. This video was instrumental in my C240 running again. Keep up the great videos.
Would it be easier to do this job by lifting the car and working from underneath? I have the 2005 C240 4Matic.
I did one today and it was a pain…tip a deep 1/4 works a whole lot better than that E8 torx
Super! But same for motor M271?
Thank you for the video it was very useful thanks again.
Nice tutorial!
That's why I hate mercedes very hard to work on.
Will that be in the same place on a ClK 200 kompressor w208?
Thanks for the video it was really fruitful, so if you do not clear the codes will it not start?
IT IS WAAYYYYY EASIER IF YOU REMOVE THE AIR MASS FLOW CENSOR
Thanks for the well done video. Sadly though, the moral of the story is this- if you own a Mercedes, you're a clown. Take these piles of junk and use them for target practice or just push them into a lake somewhere. I replaced my crankshaft position sensor 4 times. Car again won't start now. Junk junk junk cars. You'd be better off with an old used Yugo.
Hi, is the Camshaft Position Sensor located in the same spot on a 2007 w211? The same job ? And is that the fix for the code P0341 ?
Thanks
great job on your video Brian. One quick question will it be on the same location on a 2003 c320?
thanks for the video it was very helpful. one suggestion though is to remove the MAF and elbow to the throttle body. This actually gives you more room to get your hand down into the area of the sensor.