In this video we show you how to install the iWire Speed Density Wiring Kit and the iWire Hybrid MAF Wiring Kit for your IAT Sensor. We also go over the basics of how speed density tuning works.
Speed Density Wiring Kit: https://www.iwireservices.com/product-page/Subaru-Speed-Density-Wiring
Hybrid MAF Wiring Kit: https://www.iwireservices.com/product-page/hybrid-maf-adapter-for-subaru
MAP Adapter Wiring Kit: https://www.iwireservices.com/product-page/map-adapter-for-subaru
MAP Adapter Install Video: https://youtu.be/bmJCDVOw83E
Speed Density Explained: https://www.iwireservices.com/post/2018/07/16/subaru-speed-density
Other iWire Install Videos:
iWire Harness Merge Install: https://youtu.be/UnU2nsvWyAg
Grounding Kit: https://youtu.be/AS6IjyXH7Bc
AVCS Intake Manifold Kit: https://youtu.be/6FNKMngn7vo
Rear O2 Extension Harness: https://youtu.be/V8CMNl8-dgA
2.0L Subaru Bulkhead Harness: https://youtu.be/x0EMmCLQToI
2.0L Subaru Engine Harness: https://youtu.be/3-Z6qQpA0bg
Plug and Play Wideband: https://youtu.be/RmlgQVBaMc0
Plug and Play Wideband with Gauge: https://youtu.be/QRuCRuKLdG8
DBW Pedal Adapter Plate for Cable Throttle Chassis: https://youtu.be/bgqN_D-maq4
GC to GD Plug Mounting Bracket: https://youtu.be/iU3JshmXV3A
Alternator Plug Install: https://youtu.be/xVa_XzwxWMM
Coil Pack Plug Install: https://youtu.be/jbryOqxf1W8
Wiring How To Videos:
Merge Process – https://youtu.be/BvGdbt9z1_M
How to Depin a Connector – https://youtu.be/R2ekVCmRMc8
How to Crimp a Terminal – https://youtu.be/wsbsATkDBxc
How to Install a Pigtail – https://youtu.be/8zSOSQ94zHo
iWire Recommended Products:
Replacement Connectors – https://www.iwireservices.com/online-store
Fuel Pump Controller Hardwire Kit – https://www.iwireservices.com/product-page/fuel-pump-controller-hardwire-kit-for-radium-hangers-single-pump
Plug and Play Wideband – https://www.iwireservices.com/product-page/iwire-pnp-kit-for-aem-wideband-controller
Grounding Kit – https://www.iwireservices.com/product-page/iwire-grounding-kit
){kind=link}
i need a cobb for tune, or can be tune with ecuflash?
thanks
Would speed density still need a AEM 3.5bar pressure sensor as well as IAT SENSOR?
do you have to drill a hole and then weld on the bund?
Can you make hybrid ones for Honda j35z4 and newer engines?
Can i run speed density with my stock turbo 2020 STI?
Does that bunt need welded on the top mount?
Do you guys know any tuners you’d recommend in Socal?
Hey any issues with Cobb greenspeed?
Hey how's it going? I have a n/a 3.0R h6(2005 outback), have a Weapon-R intake, hi amp coils, full exhaust(has two front o2's, not either rear o2's). Would the hybrid kit work for me? I'm having troubles with the MAF on my car, little off in the idle, hesitant on takeoff. I already replaced with new denso maf, it helped but still getting a little sputtering. I was wondering if I could use the hybrid kit, install the iac on my air box? I have an on board tuner, I was going to get it tuned @ ecutek this spring/summer, just wanted to get everything done first. Came across this and sounds like a good solution. I'd appreciate it. Thank you for all the vids!
Is the bung included with the kit?
I have a 2011 sti it was tuned at speed density I have the regular MAF connected to a grimmspeed cold air intake, I still get the check engine light for MAF do I need to make a hybrid MAF?
Do u make a kit for 2g eclipse and dsm and do u use ecuflash to tune with and can u help with a tune i hv been working on
I’m looking to tap my OEM intercooler the same way you have it. How deep do you need to drill the hole? How do you prep the hole for the intercooler?
Hi do you’d do a harness merge for jdm v2 wrx?
Does this means I can use a bov for my sti instead of using cobb bpv once I have the hybrid speed density installed and a tune?
Question: you done anything with the EG-33 motor? Reason I ask, I have a low-mileage one shelved in my garage…
Good explanation! Just purchased an H6 Outback…