Buy yours here: https://www.theretrofitsource.com/infiniti-angled-morimoto-xb-led-LF-INFINITIANGLE
00:37 – 01:53 Removeable of Factory Fog Light Housing
02:05: – 03:49 Wiring the Day Time Running Lights
04:19 – 06:56 Installation of the Morimoto XB LED Fog Lights
These Morimoto XB Fog Lights are compatible with the following vehicles:
G37 SEDAN: 2010-2013 (SPORT BUMPER MAY AFFECT THIS!)
G37 COUPE IPL: 2011-2013 (SPORT BUMPER MAY AFFECT THIS!)
JX: 2013-2016
M35/M45: 2006-2010
ALTIMA: 2007-2017
JUKE: 2015-2017
MAXIMA: 2007-2015
PATHFINDER: 2013-2017
ROGUE: 2008-2017
SENTRA: 2004-2017
VERSA SEDAN: 2012-2016
REPLACES NISSAN PART #: 261509B91D, 261559B91D
NO SUBSTITUTES: If you don’t have LED powered fog lights, then you’re just behind the times! Thankfully the new Morimoto XB LED projector fog lights: Look great. Are well-built. Perform like champs. Have a virtually infinite life span. An unbeatable warranty, And best of all you won’t need to sell your soul to afford them! Many of the guys here at the shop use them on their own vehicles, and they’re easily one of our most popular product lines.
COMPATIBLE: With many modern applications from Infiniti, these complete fog light housings will swap directly in place of the original halogen units that they’re designed to replace, using all of the stock mounting locations. Check the compatibility section below for a list of known applications.
PLUG N PLAY: Wiring is easy too! The XB LED Fogs are designed to work without any special wiring. They will plug into the factory connectors for the stock fog lights and each assembly includes all necessary connectors, rubber seals, and pigtails for a plug n play install.
POWERED: By three Philips Luxeon-T 5500K LED’s that produce around 1200 raw lumens per side. The projector based optics concentrate a total of 2400 lumens of pure white light into a beam that’s super wide and perfectly distributed for use as a fog light. Make no mistake, these will produce a much different [better] result than slapping some LED replacement bulbs into your stock housings. The XB fogs meet & exceed all SAE, DOT, and ECE regulations.
WELL-BUILT: Their durable polycarbonate lens will resist the test of time, keeping the housings looking new for many years to come. The powder-coated cast aluminum housing is light-weight and much stronger than comparable plastic alternatives. Doubling as the heat-sink for the LED’s, the housings completely protect the internals from moisture and road debris. We’ve sold many thousands of these fog lights and to date, have only seen one or two develop a problem…no joke!
Find Us On Social Media:
Facebook: https://www.facebook.com/TheRetrofitSource/
Instagram: https://www.instagram.com/theretrofitsource/
Pinterest: https://www.pinterest.com/TheRetrofitSource/
){kind=link}
I have a 2013 Chevy Captiva sport, I'm looking to get this installed but I'm looking if there is a universal bracket to be able to install this fog light.
Any suggestions?
I don't have a fog light and a DRL, can I still get a DRL with this?
I have a 2016 Altima S. My car doesn’t have any fog lights but only a black cover where the lights should go. Is this install still possible?
You didn’t show the light output!!???
Hello, how exactly are you supposed to adjust the height on these? One of mine is shining lower than the other, and I haven't found a way to adjust that anywhere… Doesn't seem to have any sort of adjustment screws on them like the ones that other models have, unless I'm blind. Thanks
Do not buy these if you have a 2010-2012 Nissan Altima. The wires don’t fit and neither do the fog lights.
My 2013 doesn't have the fog lights…..noticed it when I switched out my headlight assemblies for black projector units…..LOL. I have to do a full installation….there's just a black cover where the lights should go….good tutorial though.
On a 2016 Altima with factory DRL and Fog in the same housing do I still need to tap into the parking light wire or are the just plug and play without that wire?
Do the new angled fogs for the Nissan/Infiniti’s have adjustment screws? I couldn’t aim them whenever I put them on my G.
How about non-USDM vehicles, how to run the DRLs on them?
those tap connectors will corrode the wire in couple yrs , then you start to have issues