I have a 2001 Nissan Altima and the P0340 code was pending on my code
reader. I have had a P0304 CEL code come up and have spent a lot of time
and money trying to diagnosis this problem. Would a bad camshaft position
sensor cause a misfire?
Wow, headlight went out on my 2005 Altima, dealer wanted to charge me $114
plus parts to replace. Watched a video and did it myself. Now the Camshaft
Sensor may need to be replaced, dealer wants $99 to run diagnostic, other
area mechanics want $75 – $85 to run diagnostic. The cost to replace sensor
averaging $300 bucks.
hello sr. i have 2004 altima 3.5 (6 cylinder) .few days ago my SES comes on
.i took it to auto advance,and they hooked it up with small computer. i got
this: code P0345 camshaft position sensor circuit (bank2). please help me.
thanks.
@theborg That’s nuts! Sorry about that man. I think I’m going to get a
diagnostic test run and find out which sensors are acting up and try to fix
it myself. Might blow my car apart, but at least I wont be paying those
crooks. Not very good logic, but that’s ok 🙂
i have a 04 nissan maxima se automatic the cam sensor is bad as well as the
tps my car changes gears on its own and will get stuck into fifth and then
if its stuck in fifth its hard to crank ive been told the cam sensor could
be making the tps seem bad is this true or from what ive described does it
sound like both and can you tell me where the cam sensor is on my car?
Hello, richpin. Thank youuuu for the diagram about my car elantra 2008,
with all kind sensors. that was fantasty,the first time I received an
answer to my question in a complete way. That’s what we need,
correct,good,perfect and complete answer. THAN YOUU.
){kind=link}
Hi Rich, I have a 2002 Audi a4 quattro 3.0, Automatic. Were is the crank
position sensor located?
Thanks in advanced
Misfires are ignition-related. 9/10 of the time.
I have a 2001 Nissan Altima and the P0340 code was pending on my code
reader. I have had a P0304 CEL code come up and have spent a lot of time
and money trying to diagnosis this problem. Would a bad camshaft position
sensor cause a misfire?
Metal piece broke off of old sensor while pulling it out.any advice on
getting it out magnet didnt work
The crank sensors are much different, maybe because they had a problem with
the original ones.
I noticed aftermarket cam/crank sensors look different from the originals
in those vehicles
How about an 03 Pathfinder 3.5 litre?
@lcuellar79 I believe they are the same.
so helpful, fuckin finally found a helpful video
A little harder because you have two of them on the 3.5L
I had both sensors replaced on my 2005 350Z. The Nissan dealership charged
me 4.5 hours of labor. Does that sound excesive to you?
Is it the same on a 2005 Altima?
how about the 3.5 Altima 2002
Will this be as easy to replace on a 2003 Nissan Murano?
@richpin06a …which is in the distributor? Thanks for the help!
@cebell71 Just thought I’d let you know I replaced the distributor and the
truck started right up. Thanks again for all of your insight!
The 02 and 05 2.5 are in the same place.
Wow, headlight went out on my 2005 Altima, dealer wanted to charge me $114
plus parts to replace. Watched a video and did it myself. Now the Camshaft
Sensor may need to be replaced, dealer wants $99 to run diagnostic, other
area mechanics want $75 – $85 to run diagnostic. The cost to replace sensor
averaging $300 bucks.
I haven’t reset the code yet sir but I will surely let u knw
Thx so much, I have a 2005 Murano and the cam sensors had to be replaced
twice. Good to know what they are.
hello sr. i have 2004 altima 3.5 (6 cylinder) .few days ago my SES comes on
.i took it to auto advance,and they hooked it up with small computer. i got
this: code P0345 camshaft position sensor circuit (bank2). please help me.
thanks.
Thank you for this video friend… Nissan was going to charge me $200.00
just for the labor.. I thumbs you up
@theborg That’s nuts! Sorry about that man. I think I’m going to get a
diagnostic test run and find out which sensors are acting up and try to fix
it myself. Might blow my car apart, but at least I wont be paying those
crooks. Not very good logic, but that’s ok 🙂
i have a 04 nissan maxima se automatic the cam sensor is bad as well as the
tps my car changes gears on its own and will get stuck into fifth and then
if its stuck in fifth its hard to crank ive been told the cam sensor could
be making the tps seem bad is this true or from what ive described does it
sound like both and can you tell me where the cam sensor is on my car?
where are the crankshaft position sensors for a 04 maxima? Its a 6 speed
manual.
where do you find them on a 3.5L?
I have a 99 Accord EX, could you please possibly give me some information
where the Camshaft Positioning Sensor might be on it?
Can i do this on a 2002 3.5 altima
Hello, richpin. Thank youuuu for the diagram about my car elantra 2008,
with all kind sensors. that was fantasty,the first time I received an
answer to my question in a complete way. That’s what we need,
correct,good,perfect and complete answer. THAN YOUU.
Will the sensor for a 2002 altima fit a 2005 altima? I have a 2002 altima
with a 2005 engine. By the way, thanks for the video!