Just installed the zex nitrous kit, less the bottle opener. Just a view of what I did, but might not be in order much, but very close. Wish I had the BHR thr…
Just installed the zex nitrous kit, less the bottle opener. Just a view of what I did, but might not be in order much, but very close. Wish I had the BHR thr…
You must be logged in to post a comment.
){kind=link}
How did you get the leather of the center console so pretty?
I have 150 shot on my rx8 and it’s fine. All I have is a straight through
exhaust and a k&n induction kit
@JonnyDScuba Other then the BHR Ignition kit, cooling bypass, lightened
flywheel and clutch, AEM intake, Agency exhaust, Ralco pulley kit, and
Access Port lol. It’s also 55 shot until someone comes out with something
safer for the higher shots.
The bottle warmer and purge switch locations are nicely hidden and mounted.
Nice video! Make sure to check out our other zex videos on our comp cams
channel!
@FlowzTheRhythm If I was you I would go and test drive them or find someone
that has one to give you a ride so you can have a first hand on the
handling and performance of each car that way it makes it easier to decide
what suits your wants and needs. For the videos on here of the other cars
just like the 8 you just don’t know since I’ve seen almost all your cars
getting beat by something they probably could beat themselves, or ran
faster then they should. No offense to anyone, sorry lengthy.
@FlowzTheRhythm Watching some of the 8’s race on youtube makes them look
like they can’t really do anything, but no one knows how the compression
is, tune up, maintenance, how well they can drive it, or if it’s just
staged for the car not to do as well as what you think it should.
how big of a shot of nitrous can a renesis handle?
when you installed the zex kit, were you running the stock fuel pump with
the kit?? Also how did the kit workout for you
i hope this isnt a stupid question but is the engine stock othr than
cooling mod and iam not sure if u said what shot it is or if i miss it
Please clean your engine all that work and we can see bolts and brackets
that were in need of a good cleaning…. Thats a lot of work you did wow.
Clean install.
is that a 50 shot bottle
@alterego667 lol, I did clean the engine about a week after this video,
which I wish I would of done before this video. Our road is a dirt bowl
basically, so it’s hard to keep up with it sometimes. As for the bolts I
was going to replace them with stainless since I drive this all winter
long, but I’m waiting to get them all at once. All the work was worth it
thanks.
@joshua78874 It’s a 10lb bottle set with a 55 shot at the time.
@reavrr Thank you.
Also I read that you should install the valve before the MAF sensor
otherwise the ECU does not know that the inlet temperature has dropped due
to the nitrous oxide and therefore it will run lean. What do you know about
this? Have you ever hooked up a wideband lambda gauge and checked the
air:fuel ratio? Cheers
I have that soldering iron. It takes 50 years to warm up and uses more gas
than the RX8 but its pretty good. Oh also nice nitrous kit. hahaha 🙂
Hey Synthetic, quick question. On a scale of 1 to 10, based on your cars
performance on acceleration and speed, what would you rate it as? Im
thinking about either getting the rx8, or the supra, rx7, impreza, maybe
maybe the evo, nissan 240, or the 250. Nice vid btw!
@FlowzTheRhythm One more thing lol. Go to the forums and research the
vehicles also, but you will always have the naysayers on there so don’t get
discouraged. I love my rotary engines regardless of power, or if they can
or can’t beat certain cars. Thanks by the way lol.
Stock pump. Kit worked out good with no problems.
@FlowzTheRhythm That is a hard one to pick lol. I would probably say maybe
7 since my friends have a 350z and a cobalt SS and when we go to a private
course we are side by side just about the entire length of the 1/4 mile
without the nitrous.
@reavrr Think you might need to do a little more reasearch. Here I’ll help,
and like it matters how it’s said. Middle English soudure, from
Anglo-French, from souder to solder, from Latin solidare to make solid,
from solidus solid, all from webster’s.
@FlowzTheRhythm *nissan 350z
@firechicken76 It can handle a 55 shot nicely, as long as you do your
homework and read up and understand the engine, and nitrous, as well as
using it properly.
@reavrr Not saying anyway, or anyone is right lol. Just another word that
drives people nuts. Way too many confusing words and phrases out there to
even bother with. As long as people know what I’m saying I’m happy lol.
I did a lot of research on the 8 site and haven’t heard anything about
doing that. All the instructions seem to be about the same also. I don’t
know if it’s different on the 8 cause of the engine so I just followed the
regular instructions.