Removing and reinstalling the front underbody splash 💦 shield takes about 30 minutes ⏲️ to do and can be done at home with minimal tools. Please SUBSCRIBE and LIKE 👍 if this video helped. Click on SHOW MORE to see details, tools, and all the parts you need. #SplashShield #FixCarYourself
The traditional way of installing a splash shield is by going underneath the car to remove it 🔧, which is the way it’s done in this video. However a lot of work can be done from the front of your car while kneeling.
You could reverse the process of installing this with the tools mentioned below, or you can go to the direct video of removing of the splash shield video right here:
👉 https://youtu.be/frsBU5lVJWE
ℹ️ You do not need a floor jack or car ramps, but you’ll have more space to fit underneath the car if you use either of them. Anyway ALL the tools 🧰 needed are below:
OPTIONAL:
Floor Jack https://amzn.to/3oLllOd
Jack Stands https://amzn.to/3l1NpukRamps
Car Ramps https://amzn.to/36TofIS
IF REPLACING THE SPLASH SHIELD YOU WILL NEED THE ACTUAL PART WHICH IS THIS:
👉👉👉 https://amzn.to/3rc7tO7
OR
👉👉👉 https://amzn.to/2J1EVpq
Power Drill https://amzn.to/35VxnvN
Nut Driver set 1/4″ https://amzn.to/36IvRxA
REQUIRED:
Ratchet Wrench 1/4″ https://amzn.to/3eme6rd
1/4″ Socket set deep https://amzn.to/385jKgc
Hex Shank Adapter Set https://amzn.to/34UiZ7H
Pry Bar Set https://amzn.to/3eiB9mG
Universal Rivet clips https://amzn.to/2JbMBVM
SAFTEY EQUIPMENT:
Flashlight
Gloves https://amzn.to/2HWG9BJ
Googles https://amzn.to/34PQ84o
Kneepads https://amzn.to/3kMe0eW
This video guide shows how to remove the lower engine splash shield cover guard beneath the car.
⚠️⚠️⚠️
The other video of removing the low beam light can be watched right here:
👉 https://youtu.be/xUT77lWQ-RY
However, if you want to remove the low fog beam from the side of the wheel or mud flap area that can be found here:
👉 https://youtu.be/eMjM6oTRGA8
⚠️⚠️⚠️
📋 GUIDE FOR INSTALLING THE LOWER ENGINE COVER GUARD IS BELOW:
Preparation:
1) Gather all tools as outlined above.
2) Remove bolts from old splash shield.
3) Remove as many of the gray clips as possible from the old shield with a pry bar and place on the new lower engine shield.
INSTALLATION:
1) Position and line up the splash shield underneath the car near the oil filter. It should lay or fit in a portion of the bumper guard without falling. If it falls then it’s not pushed in enough.
2) Scoot down and push and line up again the splash guard with the holes on the bumper.
3) Screw in a few bolts, and then use either a 7mm socket with a ratchet or 9/32 socket. You could also use a power drill to be faster if preferred.
At this point you can finish tightening all the bolts underneath the car or in front of the car. Their should be a total of 10 bolts to tighten.
4) Place 3 of the rivet clips which attach to the mud flap and to the splash shield located on the side of the wheel area.
5) Place the other 3 rivet clips on the opposite side.
6) Put on a couple bolts 🔩 or a clip on the center of the splash cover to provide further reinforcement.
Please SUBSCRIBE if you found this video to be helpful, and check out some of my other helpful videos.
Feel free and share this video to others or you can buy me a cup of coffee ☕ here:
➡️ https://www.buymeacoffee.com/randomcarvids
OR
👉 https://ko-fi.com/fixcaryourself
Thanks, and if possible give back to the YouTube community and make videos you think may help others.
Please LIKE 👍👍👍 AND SUBSCRIBE 🔔
Great video!!! You explained it so detailed that I was able to remove it and install the new one, on my 2014 charger. By the way I am a woman. Thank you for sharing your knowledge.
9×32 socket? LOL
Can you show what the pins or brackets are the broke off so Ik what parts I need cause my splash shield on my 2013 is completely destroyed and had to replace the front bumper
That's the "closeout panel", not the lower splash shield. The splash shield goes under the engine.
What was that tube hanging, might be a dumb question but recently lost my splash guard due to a dip and noticed the tube exposing just like the one in the video. Want to be sure it’s nothing I should be concerned about
Does this work for all Dodge? I have a 2011 challenger RT
My 300 Chrysler base model had 2bolt at the back
Please slow this down.
How you get the part? Splashguard
the speeding up if really annoying
Mine is hanging off and drags when I tried to drive it. I've barely driven it and didn't run over anything. Does the car need it? If I get someone to take it off will it damage the car? This was my late husband's car and it's getting on my nerves!!!
Hello, very good video!
I’m trying to install it on mine 300c but it has 2 bolts (one on each end) holding like 2 little bars, my question is can I take it out or will it get damaged? Thank you
Hi. When you remove the plastic clips, do they usually need replaced with new ones? Does removing them damage them?
Awesome video .. thank you for supplying the link for the splash guard .. keep up the Great Work