Car Fix DIY Videos

http://chevroletforum.com/how-tos is the leading Chevy Silverado resource for technical guides. Without brake lines, your brakes are just about useless, so it’s important to make sure they’re in good shape. For the full step-by-step article, please visit http://chevroletforum.com/how-tos/a/chevrolet-silverado-1999-2006-how-to-replace-brake-line-392749

Your truck uses rubber brake lines for certain portions of the braking system. While rubber isn’t bad, over time it can lose its shape and cause bubbles in the line with the brakes pressed.

Even if your lines haven’t failed yet, switching to a set of braided stainless steel lines can give you better peace of mind, as well as a firmer pedal feel if your rubber lines are starting to get bubbling issues.

This moderately difficult job takes 2-4 hours and costs from $45 to $250. A professional may charge anywhere from $500 to $800.

This job requires a power bleeder, drain pan, shop towels, flare wrench set, floor jack, jack stands, tire iron, flathead screwdriver, and WD-40.

Step One – Locate the brake lines you’re replacing

If you’re replacing an entire section, you need to follow the line from start to finish to decide how to get it out and how to get the new one in.

If you are cutting out an old section and splicing a new piece in, make sure you have enough room to get your tools up there.

If you are replacing an entire section starting from the master cylinder, be advised that you’ll need to be able to lift the truck body off the frame to allow clearance for both feeding the new line through as well as using tools. For those who aren’t mechanically inclined, it is suggested leaving that process to a professional.

Step Two – Raise the truck

Depending on which lines you are replacing, you’ll need to decide where to raise the truck from.
If you are only patching a center section, wheel removal may not be necessary.
Regardless, because you are dealing with the brakes, you need to set the emergency brake and chock the wheels on all sides.

Step Three – Remove the old brake line

Before undoing a brake line, line underneath the truck with shop towels where both connections will be undone to catch corrosive brake fluid.

● If you are splicing a section, using the cut off tool of your choice, make your two cuts around the section that needs to be removed. If your are replacing a piece that has rusted through, make sure your cuts are at a place where there it is a strong enough section to make a new connection; otherwise, all you will do is create the next failure point.
● If you are removing an entire section, you’ll need to trace the line from start to finish and remove it from any clamps holding it in place using your flat head screwdriver or pliers. This may include raising the cab or bed to allow proper access.
● Once the line has been undone from any clamps, you’ll need to use the proper sized flare wrench to undo the flare nut holding the line in place at each end.
● If there is severe rust on the nut, it is suggested using a lubricant such as WD-40 prior to prevent breaking the nut or the joint.
● Once it’s unbolted, you may find it easier to cut it into sections to help with removal. Be prepared though, as the line still contains fluid, so every section you cut is another potential drip point.

Step Four – Install new brake line

● If you are installing an entire section, you’ll need to route the line the same way the old line was routed.
● Once the line is in position, reattach it to any clamps that were holding the old line. Then you can tighten the nuts using your flare wrench. Be careful not to over-tighten because the nuts are made of a softer metal, which means you can round them off or strip the threading easier.
● If you are splicing a new section in, your process will be a bit more involved. You will need to chamfer the end of the brake line at both cut points to clean it up first.
● You will then need to flare both ends of the line at the cut points using a flaring tool.
● Once the lines are flared, you can attach your new section into place.

Step Five – Top off brake fluid and inspect for leaks

Top off the brake fluid reservoir, pumping the brakes one or two times, and then topping off the fluid level again. Once the reservoir has a sufficient amount of fluid, it is suggested pumping the brakes a couple more times and then inspecting your brake line connections.
Any fluid coming out is a sign of a bad connection that will need to be fixed.

Step Six – Bleed brakes

If there are no leaks, you’ll now need to bleed the brakes using a power bleeder. Since you removed a section of brake line, you introduced air into the system.
The braking system needs to operate in a vacuum to ensure proper functionality, so you’ll need to bleed the brakes to remove any air from the lines.