i would just cut the hole in the bottom with some mesh across it… just the increased air is going to do a shit ton more than leaving it stock. plus it’s easier haha
The hole on the bottom of the intake Housing should be good enough . I did the same thing MINUS the Hose . I ONLY CUT A HOLE UNDER THE HOUSING . Thats it
awesome.. now you can suck tons of water, bugs and dirt into your fiter. just get some generic 3inch pipe,couplers,hose clamps and an ebay filter. way better looking and performing. this is just ricer and ghetto. theres cheap and thats fine..then theres stupid like this.
In my case when I plan to make one, I plan to put some kind of mesh infrom of my pipe to filter out bigger shit like grass and leave’s or other junk that might go through where I place it. Also the position where I’m placing mine on my ford is gonna be next to the radiator so water getting in my intake is not a huge factor with my setup.
i have a 02 blazer and i made your ideal better i took out the filter box and ran the gutter hose and i spayed heat paint on it to keep the heat off the hose i’m getting better gas millage and you’re right you don’t have to spend a ton of money on a cold air intake
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all.
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all. it is more easy to do it the right way.
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all. it is more easy to do it the right way.
cool. Looks like a ram air kit. You may want to put some sort of mesh screen over the end of the intake to prevent dirt from clogging it… but good set up for free I think.
well it doesnt go slower…but if you’re being serious, do some reading up on modifications for increased HP. the correct answer here is…you cant tell a difference with 5 extra HP
i would just cut the hole in the bottom with some mesh across it… just the increased air is going to do a shit ton more than leaving it stock. plus it’s easier haha
That’s ridiculous. The air filter itself is what gives you better cold air intake
The hole on the bottom of the intake Housing should be good enough . I did the same thing MINUS the Hose . I ONLY CUT A HOLE UNDER THE HOUSING . Thats it
awesome.. now you can suck tons of water, bugs and dirt into your fiter. just get some generic 3inch pipe,couplers,hose clamps and an ebay filter. way better looking and performing. this is just ricer and ghetto. theres cheap and thats fine..then theres stupid like this.
Ghetto LMFAO.
red neck intake
LMAO…….. that is freaken getto…….. LMAO
does your truck have any better performance? thinking about this for my 99 z71 with a 4.8
In my case when I plan to make one, I plan to put some kind of mesh infrom of my pipe to filter out bigger shit like grass and leave’s or other junk that might go through where I place it. Also the position where I’m placing mine on my ford is gonna be next to the radiator so water getting in my intake is not a huge factor with my setup.
That is such a bad idea… So much crap will get in there now… No wonder why theres all those leaves…
your fucking duuuummmmmbbbbb you just add stuff to it
i have a 02 blazer and i made your ideal better i took out the filter box and ran the gutter hose and i spayed heat paint on it to keep the heat off the hose i’m getting better gas millage and you’re right you don’t have to spend a ton of money on a cold air intake
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all.
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all. it is more easy to do it the right way.
all you should have done was buy a performance cone air filter and hook it to your throttle body but your set up it could trap water in that gutter pipe and be suck in and mess up your truck i always say if your not gonna do it right don,t do it at all. it is more easy to do it the right way.
cool. Looks like a ram air kit. You may want to put some sort of mesh screen over the end of the intake to prevent dirt from clogging it… but good set up for free I think.
There is no way that i could put that on my stock truck and gain 30 HP. 5 is more realistic.
yep, you can do what you want..
You could also just buy some intercooler pipe and it will look a lot nicer than some plastic pipe.
Ive completely sank an engine at least 3 or 4 times in my opinion hydrolocking is a myth
This mod is dumb if u drive it in the rain or through a puddle of water itll get in the engine n possibly hydrolock it
of course…
no
What if you drive in the rain or snow? That seems like it would work its way up and get sucked in
well it doesnt go slower…but if you’re being serious, do some reading up on modifications for increased HP. the correct answer here is…you cant tell a difference with 5 extra HP
cant tell much just with this mod..id say no.