http://www.retrofitlab.com/projector-kits/bi-xenon-mini-h1-twin-kit-1.html The Audi A4 B7 is a very classic car with a luxurious appearance. Your car didn’t …
http://www.retrofitlab.com/projector-kits/bi-xenon-mini-h1-twin-kit-1.html The Audi A4 B7 is a very classic car with a luxurious appearance. Your car didn’t …
You must be logged in to post a comment.
Great job! You make it look so simple…
Can you give an advice how to open Jetta 2012 headlights? As i understand
you cannot ‘bake’ them, as the sealant used from factory is very strong.
Some people cut them…but i dont want to use that method. Thanks!
By the way, do you know the diameter of the space you’re placing it? Those
look beast!
This vid was exactly what I was looking for. Although some things happened
so fast I barely knew what you were doing, but still, thanks.
what kind of glue is used at the end? thanks
very nice, can you give me any information on retrofitting lens on new kia
rio(pride), thanks in advance
Hi! Do these fit the Skoda Octavia 2 1z3 headlights without cutting them?
The headlights are stock without projectors. I mean the lenght inside the
headlight will suffice?. And will the electric hight adjustement in the
headlights still work? Thank you!
Amazing!
On which temperature is the heat gun set?
This is the most brilliant heating method I’ve ever seen!
I never had the chance to remove my headlight cover because my microwave
oven is too small haha.
Btw. can you also use a hair dryer to heat it up? Is it sufficient enough?
What LED is that in the hi-beam corner?
I wish you guys could do that to my 07 Ford Focus. But I’m in Florida. 🙁
….I’d pay you $250 for both projectors install and installing an 8000K
HID bulb behind it.
Thanks a million on this video. Great, straight to the point, and no extra
bs.
What a retarded way of opening headlights. Just run the heat gun over the
seams for about 2-3 minutes AFTER you remove the tabs. Then pull the cover
at the lip and use the heat gun on the sealant as you pull to make it split
cleanly, Simple and quick…
Don’t you have to align your lights properly before asembling them
completely? And if yes, how is it done?
so a normal blow drier will be enough to heat up the lights to break the
seal?
as a total unit 1 enters the lens?
Are these headlights street legal? I mean – without washers and automatic
beam adjustment?
What is the time you heated a headlight?
Was this the Iris shroud?
How much is it for a pair of lights and does ist shine really white or does
in only look like xenon ?
I want to buy from you shop projector lens, but its necesary to buy butyl ?
can i reseal the headlight with the original glue ?
Hi guys. Plz tell me there is one for a MK6.5 fiesta? (2006)
Awesome job! Does the heating part for taking off the lens works also on A6
C6 headlight. I have heard that there is some different sealent used and
its not going to melt?
Nyc n clean work done !
Ah. So If I understand correctly : the way you hook it up there results in
low beam over Xenon, but you make a pass-through with the Hi-beam original
light in order to not only activate the Hi-Beam solenoid switch in the
Xenon : that way, when you Switch on Hi-beam, both the original Hi-beam
Reflector Hallogen lights up AND the Xenon retrofit goes into Hi-Beam
position. The result is in Hi-beam, you’re really throwing 2 Bulbs (one
Xenon, one original Hallogen) into Hi-beam ?
U r doing a great job. It’s not easy at all to be done at home.