Replacing an Accord Wheel Bearing Ok, here it is finally. A few of you have requested this procedure so here it is. As I said in the video I normally use a d…
Replacing an Accord Wheel Bearing Ok, here it is finally. A few of you have requested this procedure so here it is. As I said in the video I normally use a d…
You must be logged in to post a comment.
I have 208K miles on my ’98 Honda Accord. My right front bearing is
starting to scream a bit. They have never been replaced. Although you
tempted me to want to do this myself Eric, I’m worried about pressing the
bearing in/out and removing the old race (I don’t have special tool
XD45….). Perhaps I’m just lazy? Anyhow thanks for the fine Vid!!
QUESTION! 7:20 you show the new bearing already pressed into the 4-bolt
mounting section. I look on Amazon and only see the bearing (w/out 4-bolt
mount). I presume I would have to PRESS this into the old 4-bolt mount?
This is where I get nervous…Can I purchase that whole piece (bearing +
4-bolt mount) rather than pressing into old 4-bolt mount?
My local Honda-guy wants $366 (out the door) for BOTH front bearings. I
think this is a good value.
Dealership wants $950 + $100 mandatory allignment <-----Pfffffffft !!!!!!!!!!!!!!
9:35 lol 1000 subscribers . Look now on your way to HALF A MIL BABY !!
just had some honda techs fix mine, original bearing on a 96 accord. nice
to watch your vids to see how it was done. ++
thanks Eric I have been watching your videos and they have help me a lot, i
am working on 1993 honda accord, new rotors and new bearing hub, and i
would like to know how to replace the lower from ball joint on this car
looks like 30 people didn’t listen to eric and put their bearing assembly
back together right.
Eric, I have a 1997 Accord and I want to replace the front brake pads,
rotors and hub/bearing assembly roughly how long would it take a certified
mechanic to do this job…thanks
great vids Eric! Thanks!
I had a front bearing replaced on my 98 civic about 6 months ago and it’s
gone bad again. Anyway of knowing if it was an installation error or just
defective part?
What a stupid design! What the hell was Honda thinking! And they only did
this to the 90’s Accords, not the Civics..Why? Why not just keep the
standard rotor-over-hub design?
Thank you Eric!
Your videos have all the practical details that the manuals never mention.
Plus you have personality! The manuals are as dry as dust and they never
say – This one bolt is really tough to reach unless you are at least 6 feet
tall.
Thanks again Eric, you rock on youtube and give us all confidence with your
tips and tricks
Eric man you have saved me thousands!
Good job!
Hey eric another great video from you. I have learned a lot through your
channel thanks. I have a question. I have a bent hub on my honda fit. So
naturally I Ave to change the hub and bearing. The question being is ok if
I just replace the entire steering knuckle with the hub and bearing already
installed (from a junkyard). Ny thought being this would be easier
considering I do not have the tools to r & r the hub and bearing. Thanks in
advance. Oh and should I grease the the outboard splines on the drive
shaft?
Hey I just got mine replaced and they charged me 150 each is that normal?
Erick you are awesome!!
Hey Eric i have a problem chaning front wheel bearings hub 1995 Nissan can
u help me please
I had my broken barrings replaced recently and this really helped me
understand how it was done! Awesome video subscribed!
should I use a puller to remove the hub?
Thanks for sharing. Your video is very helpful.
thanks great info on all the videos!!
can you post videos of different methods of the bearing removal next time
you have the chance
Hey good vids. In case you’re curious that special tool is a flange bolt
for the underground assembly off a fire hydrant
Any suggestions on how to replace the studs off a wheel spacer? Thanks
very well made vid Eric, I like the sound effects of an audience you got
towards the end of the vid. lol Great work you always seem to amuse me when
it comes to hondas and while no one else can, maybe except for me..jk :)
“Just crested a thousand subscribers.” And now you have more than 350
thousand. Well done! Thanks so much for your videos!
I cant get the four rotor bolts loose and dont want to strip them out what
can i do
Entertaining and informative stuff.I’ve been working on my lady friends ’96
Accord.Working up to replacing the timing belts.Thanks EricTCG.
Nice video. But what about the front wheel bearing and hub removal I have
breaking stubs to removal on a 2008 Accord . I know there tool out there
that i can use to remove it .Then send it to the shop and pay 200 buck for
one wheel stud to replace.. .
Just to let you know, i realy like your videos. i have worked on cars for
45 years and i am still learning a lot. Thanks and keep them coming. as to
your detractors if they know it all why are they watching how to vids.
You’re the shit Eric….keep it up
Nice vid, will changing bearing on 87 crx, video helps alot, thanks