How to Replace the Side Engine Mount on a 2006 Acura TL

How to Replace the Side Engine Mount on a 2006 Acura TL

Brian Eslick from How to Automotive http://www.howtoautomotive.com/ takes you step-by-step through the process of replacing the side engine mount on a 2006 Acura TL.

Affiliate link mentioned in the video for Genuine Acura 50820-SEP-A21 Engine Side Mounting Rubber Assembly http://amzn.to/2hmiEPc

Affiliate link mentioned in the video for 3 Ton Heavy Duty Ultra Low Profile Steel Floor Jack with Rapid Pump Quick Lift http://amzn.to/2iCCMOd

Affiliate link mentioned in the video for Milwaukee 2457-21 3/8-in Cordless M12 Lithium-Ion Ratchet Kit http://amzn.to/2hrwK5m

Website
For more videos, tips, and to purchase recommended tools and products visit my website at: http://www.howtoautomotive.com/

Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: https://www.facebook.com/How-to-Autom…
Google+: https://plus.google.com/+HowtoAutomot…
LinkedIn: https://www.linkedin.com/in/brian-esl…

Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick

10,465
Like
Save


Comments

Me Me says:

How high should I lift the engine up ?

Livingston Rolle says:

Every time I do this my engine mount bracket is rubbing against the pulley when I tighten screws, any ideas why?

WireD M says:

As with the video for the front engine mount, I appreciate your excellent, brief, and concise video. I was done with this in about 20 minutes. I wish I could show you the condition of the mounts that I replaced.. they were cracked, leaky and not functional. I'm surprised the engine didn't fall out. All fixed up now. Again, thank you!

Gear Jammer says:

Getting ready to do both the side and front engine mounts on my 2007 Acura TL "Type-S". A few questions if that would be alright, and Thanks for your time.
#1- Is the set up and removal procedure the same on a 07 Acura TL "Type-S" as on the 06 Acura TL (non Type-S) in the video ?
#2- You say torc side mount engine bolts to 47 pounds, but you say (in your Acura front mount video, same car) to torc the mounting bolts at 40 pounds. Shouldn't they both be the same?? Thanks

Marco Arce says:

You should add that it’s a pain in the butt to crack those bolts loose.

Johnny Gamboa says:

Is it safe to jack the engine up like this with everything else still connected? I have this same exact mount that is completely trashed so will probably replace soon! Thanks Brian!

Alberto Monzon says:

Do you have to buy all the mounts?
Or can you buy them separately?

Ali Saeed says:

Is it same part for 2004?

Minh says:

so awesome man! could you do videos on the rear engine mount and the transmission mount as well? Thanks so much!

Alfredo Gomez says:

Any video on how to replace the rear engine mount or front left mount on this same vehicle?

12vgs8606 says:

Thanks for showing this; I was under impression that this was going to be lot more complicated. I have 1999 Odyssey with similar mount which really should be replaced given its age and condition and with your video I might have the courage to do it myself.

Write a comment

*