How to Replace Front Differential Mounting Bracket Bushing in GM vehicles – Hummer H3, Chevrolet Colorado, GMC Canyon
In this video I show how to change car bushing in hummer h3 front differential. This is part 1 video where I change Mounting Bracket Bushing. In my next video I will be changing cross member bushing for front differential. #car #cars #how #howto #cardiy #humman #newroad
Bushing tool that I used: https://amzn.to/3Rp8D8B
My Gears and Deals: https://www.amazon.com/shop/hummansunson
How to Replace Front Differential Mounting Bracket Bushing
00:10 – Loosen the Wheel Drive Shaft Nut
00:31 – Loosen Wheel Lug Nuts
00:41 – Before lifting – make sure vehicle doesn’t roll, and stable
00:46 – Raise wheel off ground and remove Wheel
01:07 – Disconnect Brake Lines from retaining clips
01:37 Disconnect Tie Rod from Steering Knuckle
02:08 – Remove Upper Control Arm Pinch Bolt and Nut
02:51 – Remove Wheel Drive Shaft Nut
03:10 – Remove CV Drive Shaft from Steering Knuckle
03:33 – Before removing CV Drive Shaft – place oil pan
03:38 – Remove CV Drive Shaft from Differential
04:10 – Remove Mounting Bracket Bolts
05:18 – Remove old Bushing
05:42 – Press out old Bushing
06:03 – Clean-up Mounting Bracket and Bushing housing
06:08 – Install new Bushing
06:55 – Reinstall Mounting Bracket.
07:01 – Finish tightening Bolts as per your vehicle Torq Spec
07:20 – Reinstall CV Drive Shaft – C-clip gap should point down when installing. Make sure it is properly in
08:13 – Reinstall CV Drive Dhaft into Steering Knuckle
08:20 – Follow steps in reverse to complete installation
Make sure you tighten all bolts according to your vehicle Torque Specifications
Disclaimer: Newroad assumes No liability for property damage or injury incurred as a result of any of the information contained in this video. Please consult your qualified auto technician.
Newroad cars channel
#hummer #hummerh3
0:00 Introduction
0:12 Loosen the Wheel Drive Shaft Nut
0:32 Loosen Wheel Lug Nuts
0:47 Raise Wheel off ground
0:57 Remove Wheel
1:08 Disconnect Brake Lines from Retaining Clips
2:08 Remove Upper Control Arm Pinch Bolt and Nut
5:18 Remove old Bushing
5:42 Press out old Bushing
6:09 Install new Bushing
8:20 Follow steps in reverse to complete installation
){kind=link}
As always loved your video.. one question where did you bought this bushing?
Both sides must be replaced so that it sits level—at the same height. My apologies.
Where can you find the bushings
I'll likely be doing this to my 2007 H3 sooner rather than later. Going to a Suspension shop on Monday here to get some rear spring bushings put in, but this looks like something I may be able to do in my driveway to hopefully fix a 'clunk' I'm getting in the passenger side. What bushing kit did you use? Can you share a link please?
You continue to put out great videos, keep them coming. Thanks.
Cant find bushings discontinued for passenger side..what part # did u use?
What would you feel if the bushing is gone?
I need those bushings where do I buy them
Thanks a lot for your videos. Could this be the reason why there is a play between the front diff and the cv axle?
Part number please
Where did you get the bushings?
Just curious I know you have had your H3 for a long time. What year is yours and how do you like it? I’ve been looking at buying one for off-roading but the 5 cylinder I’m not sure of.
Great that you add in all the torque specs as well as any issues you encountered. Thx again!
Спасибо)
I know it's not as easy as in video, but great demonstration and straight to the point. Thanks