SETTING UP TIMING BELT ON HONDA ACURA 3.2L 3.5L 3.7L J-SERIES ENGINE IN DETAILS!!!

SETTING UP TIMING BELT ON HONDA ACURA 3.2L 3.5L 3.7L J-SERIES ENGINE IN DETAILS!!!

This video will show you how to set up timing belt on any Honda or Acura 3.2L, 3.5L, 3.7L J-SERIES engine.

THIS IS THE ONLY HONDA ACURA CRANK PULLEY REMOVAL TOOL I RECOMMEND.

This is the only scan tool I recommend.
full version

10 models all systems

https://www.amazon.com/LAUNCH-Icarscan-DiagnosticTool-Systems-Android/dp/B0753G14V3/ref=as_sl_pc_tf_til?tag=melniksmotors-20&linkCode=w00&linkId=23c1a9ab248686fed01d8206c140bbc2&creativeASIN=B0753G14V3
Disclaimer:
Warnings And Caution!!!!

If you follow the procedures, techniques and methods shown in this video, be aware that you follow them at your own risk.

Under no circumstances will the author(s) and/or publisher(s) of www.youtube.com/user/melniksmotors (melniks automotive) be held liable for any injuries or damages, direct or consequential, incurred by any person who attempts to follow the examples shown herein.

1,025,405
Like
Save


Comments

KP Audi R8 says:

good video love it, thank you bro good jobs

DCR 132 says:

Nice video , I got 20212 mdx making noise from cam shaft bank 1 under upper timing belt cover. Not sure what’s causing it, here’s link to it…

https://youtu.be/W2H4-Bk2PZ4

Caleb Hodum says:

What's the difference between the 3.5 V6 in the 2009 honda accord and the 3.5 V6 in the 2012 acura TL

Scratchthejeepguy says:

Quick question for you. I'm installing a timing belt kit. I pulled my crankshaft pulley off, then pulled the lower TB cover off. The TB Idler pulley had the ball bearings falling out and was completely shot… when I turned the crank to line up the marks, the front cam mark was off about one tooth, and the rear cam was off by about 3 teeth. Can I just remove the TB, manually turn the cams the little bit needed to line up, then reinstall all the pulleys and belt again? The car was running fine, but I think the cam pulleys slipped a few teeth when the idler pulley let go.

James Corbett says:

What was knocking when you were turning the engine

Conner says:

I never marked anything before taking the old belt off, just wondering as long as the 3 marks are lined up and TDC, everything should be fine no?

Redi Hoxha says:

i'ts the same job and for Acura RDX 2.3L but has only one camshaft?

Danny's Auto Repair says:

Great video thanks

Anthony Merc says:

Question for you about the water pump. In a situation when the water pump isn't being removed. If when removing the 3 housing bolts it starts to leak a bit of coolant is that seal permanently broke. Other words once the 3 bolts are back in it is likely it will leak again without new RTV?

Arturo Barraza says:

hello George, one question, I have a 2006 accord, it had the classic noise of the tensor as a sewing machine, I changed it and that sound was removed, but now the tensor leaked oil, what could that fault be? why did it leak? the band was placed correctly, so much so that the car worked normally for 15 days…. thank for readme

SOHIB SH says:

Thank you for advice
Very helpful video

Elijah Simmons says:

I need help

hand h says:

You didn't put the bettery cramp bolt on the idler pully tensiner. Is it ok? Why do we have to put the bettery cramp bolt? Many guys don't put the bettery cramp bolt on it. Why? We don't need it. 2007 Oddyssey and your video show the bolt thread and hold.

Craig Goldsmith says:

I never got the new timing belt on. When I was installing it the rear cam move out of position. The right cam and crankshaft are lined up Perfectly. The rear cam line is facing the fire wall. What do I do?

Comments are disabled for this post.