In this video I show how to program a Honda key FOB transmitter so that it works with the door lock system. If the master power window switch (window control unit) is replaced on older Hondas, this programming must be done. On many older Honda vehicles it is possible to do this programming without the […]
We repair a remote wireless entry key transmitter by replacing switches. This applies to 97-2004 model year 911s and Boxsters with parts purchased at batee.com. Bryan A. Thompson batee.com Parts and Repair
Short video on how to fix or repair a broken / faulty Nissan Sentra car remote / transmitter. Video also shows how to change out the battery. This card remot…
Without Smart Entry System 1. Close and lock all doors with the driver’s side power lock/unlock switch. 2. Insert key into ignition and remove it from the ig…
1. Enter 5-digit permanent entry code into the keyless entry keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors wil…
XJ 1. Open drivers door 2. Hold the highbeam selector arm towards you 3. Insert ignition key and key to first position (acc) 4. Release the high beam selecto…
How To Replace A Kia Cerato Transmitter Battery Battery Type CR2032 The 2013 Kia Cerato transmitter uses a 3 volt lithium battery which normaly lasts for several years. To replace the transmitter…
Follow the below how to: 1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm progra…
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 2. Within 20 …
1. Enter 5-digit permanent entry code into the keyless entry keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors wil…
Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also. 1. Locate the programming connect…
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 2. Within 20 …
1. Close all doors, open drivers door, key out of ignition. 2. Lock and Unlock the drivers door using the power lock switch on door panel. 3. Insert key into…
1. Close and lock all doors with the driver’s side power lock/unlock switch. 2. Insert key into ignition and remove it from the ignition key cylinder at leas…
1.Remove key from ignition. 2.Close all doors. 3.Open driver side door and leave open. 4.Perform the following steps within 24 seconds. a. Insert key in igni…
1.Remove key from ignition. 2.Close all doors. 3.Open driver side door and leave open. 4.Perform the following steps within 24 seconds. a. Insert key in igni…
1. Turn ignition to RUN or ACC. 2. Momentarily jump pins in programming connector located behind glove box. All doors will lock then unlock to confirm progra…
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 2. Within 20 …
1. Make sure ignition is in the OFF position. 2. Locate the programming connector in the trunk (drivers side). It is a plastic connector with two wires leadi…
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. 2. Within 20 …
TRANSMITTER PROGRAMMING NOTE: The remote keyless entry system is equipped with 2 transmitters, having 2 unique vehicle access codes programmed into the wirel…
Follow these instructions: 1. Turn ignition to RUN or ACC. 2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will…
You have one programmed remote and you want to add another. 1. Vehicle must be off. 2. Place the working remote(s) in the cupholder. Have the new remote with…
If your 1999 Grand Am was built late in 1999 you will have to go to a Locksmith or Dealership to get your remote programmed. Click here to find a Locksmith i…
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not w…
Note : All transmitters being serviced must be available. If the learning process is carried out without having all the transmitters present, all previous tr…
1. Close and lock all doors using power switch on drivers door panel. 2. Insert and remove key from ignition (Do Not Turn) at least 6 times within 10 seconds…
1. Remove key from ignition switch. 2. Close all doors. 3. Open drivers door 4. Insert key and turn to ON position and within 10 seconds turn key off and rem…
1. Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door is open and insert key in ignition. 2. Turn igniti…
How to replace the battery on a Jeep key fob transmitter/remote – if your remote doesn’t have a battery door. My key is from a 2010 Jeep Grand Cherokee.
ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not w…
1. Close all doors. 2. Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release. 3. Insert and remove key from …
1. Turn ignition to RUN or ACC. 2. Momentarily jump pins in programming connector located behind glove box. The horn will chirp to confirm programming mode. …