Buy Now!
New CV Axle Assembly from 1AAuto.com https://trq.video/ia-1AACV00476
A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install one in your 2007-2012 Nissan Sentra.
• Check here for more videos on the 2007-2012 Nissan Sentra http://www.youtube.com/playlist?list=PLJVpHWuCEUX9XG93DwGcDeDYoCtRvME2j
This repair was done on a 2010 Nissan Sentra Base 2.0L and the process should be similar on the following vehicles:
2007 Nissan Sentra
2008 Nissan Sentra
2009 Nissan Sentra
2010 Nissan Sentra
2011 Nissan Sentra
2012 Nissan Sentra
Tools you will need:
• Pry Bar https://trq.video/ofX-1AXAA00020
• 21mm wrench
• 21mm Socket
• 32mm Socket https://trq.video/oJ-1AAST00003
• Pliers
• Side Cutters
• Torque Wrench https://trq.video/onT-1AXAA00044
• Center Punch https://trq.video/oba-1AXAA00055
• Hammer
• Rubber Mallet
Subscribe: https://www.youtube.com/channel/UCWCdsftsTqYMO7cA_5Sc-yA?sub_confirmation=1
Check out our playlist:
Nissan Sentra 2007-2012: https://www.youtube.com/playlist?list=PLJVpHWuCEUX9XG93DwGcDeDYoCtRvME2j
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
){kind=link}
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Straight, direct videos love these thanks a bunch can you make one of 11 Sentra transmission removal and replacement
Make sure you PB blast all your bolts prior or have an air gun for your axle nut
Wheres the video for the passenger side?
@ 1:33 it’s a 21mm socket FYI
No one shows putting the fluid back in
The Axle Nut needs to be removed before rasing the front of the vehicle or somebody needs to press and hold the brakes, which might not be eficient and safe and might damage the transmission.. grounded and parked vehicle with hand brakes on worked for me..
Is there supposed to be a gap between the cv axle and the transmission or does it go right against it ?
Yeh right.these Nissans are a joke.it is not that easy pulling the axle out.im still fighting it.i guess I'm gonna have to buy one of those cv puller tools. These videos always make it seem so easy.
Can you use a different anti seize
on the spline or does it have to be copper never seize
Oh nice a 7 minute job…. 7 days later . All done ✅
Would this be the same on a 2016 Nissan Sentra?
I like the five lug to 4 lug conversion at 0:20
What if I try to take off the cv axle bolt and the whole cv axles spins with the wrench?
I WANTED TO SEE THE INNER PART THAT GOES INTO TRANSMISSION, IS THERE A MEDAL RING, NO AXEL SEAL NEEDED?
Would this be the same process on a manual 2007 nissan sentra 2.0?
Thanks for the video! Did you have to top off the trans fluid after? Mine has the CVT. Thanks!
This shouldn't change the alignment though
Do you need to lube the spline that goes inside the transmission?
How on earth did you pull that CV joint out of the transmission so easily?
Old boy works as fast as he talks. Red thread locker? Cheers!
Why do some have ABS ring? Is that required for cars with ABS?
You don’t have to remove link stabilizer like maxima and Altima?
What happens if some of all transmission fluid, spills out, do I have to replace transmission fluid