Ford Escape Mazda Tribute Mercury Mariner Timing Chain Replacement and Timing Marks

Ford Escape Mazda Tribute Mercury Mariner Timing Chain Replacement and Timing Marks

Ford Escape Mazda Tribute Mercury Mariner Timing Chain Replacement and Timing Marks
► Our Website for Tools, Parts and more Videos: http://mechaniclifestyle.com

In this video we are going to show you how to remove and replace the timing chain on a Ford Escape 3.0 Engine. This will also work for the Mercury Mariner, Mazda Tribute, Mazda MPV and Mazda 6. All of them share the same group of 3.0 Ford Engine.
This engine jumped a few teeth on the timing chain which caused the engine to run very badly and it even sounded like diesel. Most people will go ahead and replace the whole engine but in most cases the valves will be ok and you will not need new engine all you need to do is put a new timing Chain Kit. It is recommended to replace the timing chain at around 100-120k miles on this engine. We have repaired many in the past that jump the timing around 150k miles.
We purchased the timing chain kit on eBay. It is made in the USA and it cost only around $100 with free shipping.
This video demonstrated how to install the new chain and how to time the engine. The timing marks on this models are a little confusing but hopefully this video will clear things up and help you with the timing marks.
This should work and be almost the same procedure for:
Ford Escape 3.0 V6
Mercury Mariner 3.0 V6
Mazda MPV 3.0 V6
Mazda TRIBUTE 3.0 V6
Mazda 6 3.0 V6

► 2ND Channel Subscribe: http://bit.ly/2a86p9Z

►►Honest Product Review Channel: http://bit.ly/2ygqUcy

► BMW E46 ZHP PROJECT http://bit.ly/2g8tOa9

► Ford Fiesta ST BUILD http://bit.ly/2a59UKp

► 2013 GT86 Project Playlist: http://bit.ly/2dz4xY1

Please LIKE , COMMENT & SUBSCRIBE for More DIY VIDEOS that Could SAVE YOU BIG $$$$$$$!!!

5 NEW VIDEOS EVERY WEEK!

Thank you!

*Disclaimer
We, World Mechanics, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not World Mechanics.

303,960
Like
Save


Comments

World Mechanics says:

⛐ Check out our Garage to see what tools we use and recommend:
https://www.amazon.com/shop/worldmechanics

⛐ Subscribe and hit the notification bell by the subscribe button for new videos: https://www.youtube.com/channel/UCJ9xpq0qUZevSEdBSFqO2ow

⛐ Our GoFundme Page: https://www.gofundme.com/auto-repair-guys

Sindy Paola says:

cuantas millas de recorrido se renplasa kit timing

Spin Mouth says:

Timing chain marks diagram link?

Mayo Pierre says:

Montre moi premiere cylindre s'il vous plait

nic5309 says:

I am doing the exact same job the same cam is jumped on mine as yours was only question i have is can i just turn the cam back the three or four teeth it is out when i take the chain off any respose would help thanks

TheRedLatino says:

At how many miles do you have to change the timing chain. 2005 mazda mpv LX.

John Queen says:

I have a yellow 2002 v6 I just got and it needs this done. Do u use any lock tight on those two bolt on the tensioner? I can do mechanic work but not sure about that? Thanks

E War says:

2002 MAZDA TRIBUTE 3.0L V6

Replaced the RH (Firewall) cylinder head but did not set the crankshaft at the 3 OC position. Found instructions later and tried to align cam and crank after watching your video. Could not rotate engine so I went to front timing chain and tried to align marks (another mistake because this chain had never been removed). Then aligned rear. Reassembled but engine would not start. Removed cylinder head, cleaned head and reassembled. Started at # 1-TDC, 3 OC put rear chain on but could not rotate engine.

My next idea is to remove rear chain, move chank to 3 OC position and rotate engine 1 and 2/3 turns to 11 OC and align front chain per video. Then go to 3 OC and align rear chain. Rotate engine. Do you have any suggestions? Did I miss something? Any help is appreciated.

u_only_live_once says:

Hello, i have a 2004 escape with a p1336, p2197 and p2198. Sounds like chain rattle did you get codes when yours jumped time? Thanks

Flip R says:

Did you have engine light on. Or what Dtc you had?

Crazy Talk says:

Where can I find installation diagram? Mocha timing chain kit didn't include instructions.

Nour Jazzar says:

I have a question?

Harout Aroyan says:

hi I have question about mazda 6 2007 3.0 engine if is timing belt jumping is make bending to valve

Comments are disabled for this post.