How to Install BALL JOINTS: Jeep Wrangler Dana 30

How to Install BALL JOINTS: Jeep Wrangler Dana 30

How to remove ball joints video: https://youtu.be/WzqrK22X5xI
TIPS on Ball Joint replacement: https://youtu.be/yLyg7RKdW8M

Dana 30 Upper Ball Joint: https://amzn.to/36GuDAN
Dana 30 Lower Ball Joint: https://amzn.to/2tfu7Mv
3 Ton Floor Jack: https://amzn.to/38tkZ6s
3 Ton Jack Stand: https://amzn.to/37njUvr
Ball Joint Press Kit: https://amzn.to/2vxwEm2

Proudly sponsored by Enginetech https://enginetech.com/
Engine rebuild kit I used on my 4.0L rebuild: https://amzn.to/2WuNdbu

If my videos have helped you save some money , and you would like to give back to the JeepSolid Garage, consider joining my Patreon page!! There’s no obligation though. I am happy to help others out, but it does take a lot of my time.
https://www.patreon.com/JeepSolid

👨‍🔧 A few of my favorite tools 👇
Milwaukee 3/8 Cordless Ratchet: https://amzn.to/39x7WAO

24″ Breaker Bar: https://amzn.to/2RnuSNC

Craftsman Torque Wrench: https://amzn.to/2Wj7JiD

Extendable Socket Wrench: https://amzn.to/2LJNV2k

1/2″ Craftsman Impact Driver I use. Love this thing
http://amzn.to/2fTDoTR

Dewalt 1/4 impact driver: http://amzn.to/2GYEJ4w
Be sure to get the kit with 2 batteries. You’ll be glad you did!

Craftsman 165 Mechanics Tool Set: http://amzn.to/2GXRlIg
Excellent tool set that will last a lifetime.

Oil filter Wrench: https://amzn.to/2IbgT9e

Large Capacity Oil Drain Pan: https://amzn.to/2OjqXjh

Subscribe: https://www.youtube.com/jeepsolid

Follow Me!!
Facebook: https://www.facebook.com/watchjeepsolid/
Instagram: https://www.instagram.com/jeepsolid/
Twitter: https://twitter.com/dale_jeepsolid

Professional business inquires: email me at dale@jeepsolid.com

#jeepyj #jeepwrangler #jeeps

Some of the links provided are affiliate links, where I earn a very very very small commission for directing you to the website. If you make a purchase, it does not increase your cost, but helps me fund my channel. Thanks for watching JeepSolid. I am not a certified mechanic, just a hobbyist who enjoys working on Jeeps.

4,865
Like
Save


Comments

Joe Red says:

Just wanted to say thanks, I fought with swapping my ball joints a few hours before I found your videos.

Bob Bemoras says:

Snap ring on lower doesn't fit. 1 side is angled where the ball joint is pressed.

EMCal says:

Next time make sure you lineup the Cotter pin hole from front to back of the Jeep

john pellow says:

What is the white thing on the axle outside of the knuckle?

Ken Doney says:

Anti-seize!!! Can preach enough to others to use anti-seize on the hub bearing and bolts.

William Jones says:

What’s up?! Just subbed to your channel. Why don’t you use followsm . c o m to promote your videos!?

antlese says:

You make it look easy.

Rudy Bishop says:

Throw the ball joints in the frig overnight and a light bulb on the knuckle for an hour and the parts will fall in – good stuff from a mill valley 03 TJ and 93 XJ owner

Jeep Ford Guy says:

If mark hoppus was a mechanic

dissociative cat says:

tootsies the real boss

Gordon GMan says:

Job well done..

BroncoSolid says:

This feels familiar

Comments are disabled for this post.