INFINITI G35 / Nissan 350z – Fix Clutch Pedal – Bleed Install Slave Cylinder

INFINITI G35 / Nissan 350z – Fix Clutch Pedal – Bleed Install Slave Cylinder

I show you how to fix a sticky clutch pedal and how to bleed the system, along with installing a new slave cylinder.

Please subscribe to my channel for some of the best content on the G35.

350 HP G35 – Dyno Tuned Gain +37whp/45wtq

Performance Mods:
– KW v3 Coilovers
– Injen CAI
– NWP 75mm throttle body
– Motordyne MREV2
– Motordyne 5/16th spacer
– Motordyne v3 ART pipes
– Motordyne Shockwave TDX2 exhaust.

56,517
Like
Save


Comments

driftez says:

thx for video, shaft goes in the opposite direction though. grooved end facing outwards

Lalo McBrain says:

It’s the same for g37?

Corey P says:

How did you get it for 38. O’Reilly’s is double

luis linares says:

Hey Motordyne was wondering what’s the best brake fluid for the clutch! It’s my daily btw. And how much do I have to buy so I bleed it and be good with it

Jake Vickers says:

Hey man my clutch is slipping, it started slipping more and more without me driving it much, could this be the slave cylinder?

Fin says:

Even when the pressure is built up do u still depress the clutch to the floor?

Fin says:

What if it doesnt move? Master cylinder

jose salgado says:

Did you have the brake fluid cap on when you did the bleeding ?

Sinul says:

I changed my slave and my clutch is very easy to put in and it won’t come back up. After I replaced it when bleeding it it just won’t bleed I did everything the same way I’m tripping rn

Lou F says:

My g wont go into gear when the car on what could this be help plz

Mr Franklin says:

Recently did a clutch change now the shifter won't go into any gear even with the clutch fully disengaged wether the car is on or off. The shifter only goes to the right any ideas what's happening?

Corey Will says:

Very helpful video. Any tips on cleaning that junk out the reservoir?

Randy Kittelson says:

ok your good to go, You can leave

PISTON TECH says:

CD009 with the cylinder outside?

jnagime says:

I have a 03 350z and my has a cover over the Slave?

George_z34 says:

Can this work if the line is completely dry? Having trouble getting fluid down the hose

Aaron Baggest says:

Where did you purchase the gtr brake fluid?

mike holt says:

Was the slave cylinder that you removed leaking or was it just affected by heat and the elements causing it to stick.

Clit Commander says:

Can you tell me why sometimes its hard for me to put my shifter into gear, especially when i drive the hell out of it. Ill be driving my car normally than when i stop at a red light or stop sign i try to put my car in first gear and its like it wont go in that gear or any gear… i have to use all my might to force my shifter into gear…and btw i have a new transmission and clutch. – Is my master or slave cylinder bad?

Fin says:

my clutch sticks to the floor after replacing the slave cylinder. what else can it be?

kent cuzco says:

Is it suppose to feel a lil hard on the clutch pedal?

Juan Ortiz says:

@motordyne g35… Do you have the tipical chatter noise from the clutch/flywheel? If yes, can you tell me if there is a solution for that? Thanks!

Daniel Omole says:

I did my shave and the clutch line going to it is leaking now why might that be? Is it the washers?

kent cuzco says:

Hey bro , question how would I know if my 2006 g35 coupe is base or sport ? I’m new to g35 to be honest

Benjamin Keller says:

Appreciate the video, my son and I did the same to mine. Probably will need to bleed it out again. Kudos!!!

Comments are disabled for this post.