In this episode we cover some of the more common lenses you will need to remove to install LED lighting. More at www.collegehillshonda.com and www.diyhonda.com.
In this episode we cover some of the more common lenses you will need to remove to install LED lighting. More at www.collegehillshonda.com and www.diyhonda.com.
You must be logged in to post a comment.
Each vehicle dash removal is going to be different. It would be best to start with a vehicle service manual.
How do I change the lights on my dash for the vents and such?
Thanks for the heads up. Was searching the forums& finally saw your comment. Just completed in 5 mins.
Episode 196.
can u put a video for 2014 ody. installed the roof rack
Yep, figured it out.
Mine is Chevrolet Beat. Its the 194 T10 Wedge type itself.
Thanks for your reply 🙂
Each car is a little different. Typically the generic bulb base is a 194.
Hi very good video tutorial.
I am looking to replace the trunk light of my car, which is same as the model you replaced in the second part of the video (single LED).
I would like to know it’s type so that i can buy an LED version of it. Thanks 🙂
Excellent!!!
Thank you i finally got it!!
Sometimes those can be tricky. You can try putting a shop towel around the bulb and tugging on it gently with some pliers. Just don’t squeeze too tight.
I got the license plate light cover off but the bulb is in very tight. What should i do????
On the Odyssey, you do not have to remove the license plate from the outside. Open the door and there’s a plastic panel on the rear door you can remove. Once you remove the rear panel, you can access the license plate lights from the rear. Just pop out the gray harness, not the clear lens, and swap out bulbs. Just did mine, very fast and easy! Thanks for the great video.
Thanks for the electrical tape tip. I’m currently modding my ’13 Crosstour. I used those 5 LED bulbs in the doors, hatch, license and glovebox. The glove box was easy when you know. Twist out from behind the cage mount. Getting the three roof quads today and visor sticks tomorrow, and done! Awesome inexpensive mod. Just be careful prying off the lenses.
We do have those for the new Accord. A small screwdriver will pop off those lenses.
how would you replace the sunvisor mirror bulbs to led?
Thank u VERY MUCH i was about to brake my maps lights lol!
Watch the video.
Not required but useful. You just want to avoid any contact with the electronics on the back of the bulb with any metal above it. You can loosely put some electrical tape on the back or spray it with electrical insulation. You may find that you don’t need any at all depending on what vehicle you are putting them in.
Where I can buy these led lights for my honda accord 2003 sedan? ??
How do i cover the back of the 4 led With electric tape?
Thank you!!! Although I have an idea how to do it, I wanted to make sure not to break the tabs. I will upgrading to LED bulbs next week. Appreciate your expertise!!!
Thanks for the awesome vid!
That will depend on the car. There are different style bulbs for different cars. If you need help give us a call.
i have a problem i put the led light in my car but in 2 doors they dont work at all..
what to do? the voltage in front left door is 6,4volts,rear left 7,4 volts, right side of the care is all 12v..
thanks. got it out with electrical tape + nose pliers.
Try a cloth and some pliers. Just be careful not to squeeze too hard.
great … i have a problem …
How the heck do you get the trunk light bulb out? its so small i can’t grab it.
I got my white LED set in for my 2010 Accord. The lights have 12 reflector bulbs instead of the 4 in this video. Also, the components on the back side are no longer there. Looks like they upgraded the bulbs so there’s no need to worry about electrical tape coverage. My interior looks astounding!
Can I change all the lights on my 2006 EXL Odyssey?
Let me know what I exactly need to pimp up my ODY
Visit our web site and we will have the LEDs listed there that you will need.
Hey guys, I drive a 2013 honda accord coupe ex-l/navi! I will really appreciate if you guys tell me what kinda LEDs i will need for the map/ceiling and the doors lights! I tried the owner Manuel it doesn’t say anything abt it! They kinda look like these odyssey ones!
Yes. Standard bulbs can be upwards of 8 watts. LEDs 1 watt.
since they’re LED.. do they use less energy then a standard bulb?
butterknife
Nice video! Very informative and helpful!
2013 odyssey, you need to go from inside the rear door panel to replace the plate lights. Impossible to go from outside without removing the chrome panel.
We do not stock them in colors.
do have them in blue?
Thanks!!
The light bar does not have replaceable bulbs.
Thanks. But isn’t that the whole assembly? Just need to replace the existing Bulb with LEDs. Thanks!
08F13-S30-0M110