Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com https://www.1aauto.com/*/i/1ASHF00341?utm_source=YouTube&utm_medium=description&utm_campaign=videodesc&utm_term=CxWJAy5VFow
BUY THE PART:
CLICK “SHOW MORE” TO SEE INSTRUCTIONS BELOW:
1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning wheel bearing hub. This video is applicable to the 06, 07, 08 Dodge Ram
🔧 List of tools used:
• Flat Blade Screwdriver http://1aau.to/tSp/1AXAA00013
• Pry Bar http://1aau.to/tau/1AXAA00020
• 18mm Socket http://1aau.to/tfD/1AXAA00043
• 21mm Socket http://1aau.to/tfD/1AXAA00043
• 22mm Socket http://1aau.to/ta/1AXAA00266
• 35mm Socket http://1aau.to/tm/1AAST00005
• Needle nose pliers http://1aau.to/tb7/1AXAA00051
• Needle nose pliers http://1aau.to/tb7/1AXAA00052
• Torque Wrench http://1aau.to/teb/1AXAA00044
• Bungee Cord
• Floor Jack http://1aau.to/tdT/1AXAA00068
• Hammer http://1aau.to/tbD/1AXAA00091
• Jack Stands http://1aau.to/tdW/1AXAA00065
For More Info visit us at http://1aau.to/h/TC/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
On my 2006 the left side has the wheel speed sensor, the right side does not, does this sound right?
Is this the same process for 2007 Dodge Durango
Very simple. Thanks for sharing. The two wheel drive is a lil easier
question. If I needed to change out the whole drive shaft does it just pull away or out from the other end? and then align the new one and pus it in or what is in detail to replace the shaft? thanks
You might want to mention that you don't have to disconnect the tie rod or upper control arm on the 2wd models. Just pulled mine out of my 2007 1500, and was able to get it without either of those due to no front drive axle. It's a beast to knock that sucker out after over 175k miles, though. My dust shield needed a little straightening after I got it a couple times with the hammer.
Very good video! Just have a question. I have a 2006 Dodge Ram 1500 and do not see any sensor connected to the spindle. In fact there is no connection at all. I don't see any ABS wiring either. Please help.
do you have to have the the abs sensor
I like this guys videos. My tie rod but is just spinning, sprayed with WD 40 and will let it sit over nite.
For the love of god make sure you have a strut and not a coil over like mine because following these steps will kill you if you have mine which is a 2007 dodge ram! side note if you have the 2007 dodge ram 1500 laramie you can just release the tie rod end and turn the assemble and remove without ever releasing the upper control arm.
My father's 2009 Dodge Ram hub bearing assembly was no good . He took it to a shop since he was on the road. The gentleman (lol) at the counter quoted him 400 for the hub and 200 for labor. He called me immediately , I found it for 119 and being that , I've done this plenty of times it took 30 minutes. It was two wheel drive so it was that much easier. These videos are a great way to learn,If your inexperienced.
Is there any difference between this job on this truck and the same job on a 2012 Ram 1500?
Great step by step video!
This is the best & most comprehensive video on this subject I've seen. Thank you for making it.