I made this video of Removing a HEMI engine from a Chrysler 300 but the procedures are the same for the Dodge Charger HEMI. This is just a overlook on what all is involved in removing one of this engines, that way you can have an Idea.
Thanks for looking.
Follow me on twitter.
https://twitter.com/shospeed
My Gaming Channel
https://www.youtube.com/channel/UCPm7AlDYM_Ko2S-beEY_6Sw
Instagram
https://www.instagram.com/falcons_hobbies/
*** If the video was helpful, remember to give it a “thumbs up” and subscribe. ***
Disclaimer:
Due to factors beyond the control of Falcons Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Falcons Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in my video. Use this information at your own risk. Falcons Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Falcons Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Falcons Garage.
){kind=link}
Did you support the tranny when you separated it from the engine?
Just did put a new engine in and it’s something that is wired wrong making the ground wire hot and start smoking ? You know what I could possibly have wired wrong
Hey did you have to remove the transmission lines that go to the radiator from the bell housing ? Or was it just the belt housing bolts and the starter bolts you undid? Thanks
So, may it also possible to take the Engine out, and leave the AC in it ?
Or do you don't recommend this ?
Greeting from germany
do you have to remove the harmonic balancer?
Never done this before and mechanic skills aren’t so hot but how long would this take
Do you have to support the transmission with a jack when you unbolt the housing and flywheel?
Will a 5.7 out of a charger fit a 2011 dodge Durango 5.7
Hey man I have a 2009 Chrysler 300 5.7l and I want to upgrade my pulleys but I’m not finding the right ones for my car. Can I instal parts that go on the charges engine to my Chrysler since they are almost identical??
Does a engine from a 2006 dodge charger 5.7 hemi fit a 2006 chrysler 300c 5.7 hemi without any modifications, like will it bolt right in? Or do i have to change computers or anything like that ? Im doing a swap
Great video.. Thanks for taking the time to make it.. Do you have a video on installing this particular engine?
Once I finish an engine swap, do I need to go to the dealership to "reset" the computer?
Great video really helpful
Great video very helpful for working on my aunt's car
Will a 2007 Chrysler 300c V8 5.7 liter AWD fit in a 2006 Chrysler 300c V8 5.7 liter RWD
Thanks to you bro I got my 2012 chrysler 300 srt’s 392 ALMOST ready to take out. The fan assembly for the 392 was harder to take out cause the engine is big but I managed to wiggle it out. Pretty sure there was an easier way but I got it out lol anyways nice video man you helped me a lot it’s my first time too btw.
Can a 2006 dodge Charger motor fit n a dodge Chrysler???
Do you think a 2007 Chrysler 300C AWD engine would fit a 2008 Dodge Charger R/T RWD without problem?
Do i need to support the trans
good video i plan to build my 2008 hemi with just a bigger stroke and cam. do you know a way to put on long tubes with out removing the motor tho if not its all good man.
Can this be dropped from the subframe on a lift ?
How about removing the front bumper, radiators, etc…would it be easier to pull the engine out that way?
So, how long did it take from start to finish? I'm trying to see how long it would take me to pull a Hemi out of a wrecking yard.
My 2005 chrysler 300c motor went out. I found a 2014 chrysler 5.7 motor. Is there any mods imma have to do in order to run it.
My charger has a dropped valve seat, and it scattered a piston down into the oil pan.
I'll be removing the motor for replacement, and this video was very helpful!
Quick question for ya. I was able to unbolt the A/C compressor and just moved it over next to the wheel well. Did you have another reason that you disconnected yours besides clearance?
Thank you so much for making the video! It's really helped me visualize each step as I'm tearing this down.