Buy Now!
New Exhaust Manifold & Gasket Kit from 1AAuto.com http://1aau.to/ia/1AEEM00657
1A Auto shows you how to repair, install, fix, change or replace a cracked, leaking or warped engine exhaust manifold. This video is applicable to the 00, 01, 02, 03, 04, 05, 06, Chevy Tahoe, Suburban, or Silverado pickup truck; or GMC Yukon, or Sierra.
🔧 List of tools used:
• 10mm Socket http://1aau.to/oZT/1AXAA00017
• 15mm Socket http://1aau.to/o9o/1AXAA00015
• Needle nose pliers http://1aau.to/onM/1AXAA00051
• Needle nose pliers http://1aau.to/onM/1AXAA00052
• Pipe Wrench
• Ratchet http://1aau.to/oaqd/1AXAA00016
• Socket Extensions http://1aau.to/o9o/1AXAA00015
• Torque Wrench http://1aau.to/ow3/1AXAA00044
• Rust Penetrant
• Jack Stands http://1aau.to/ovy/1AXAA00065
• Wire Brush http://1aau.to/oeX/1AXAA00079
For More Info visit us at http://1aau.to/h/bqM/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto http://1aau.to/m/Visit-1AAuto
√ Do it Yourself
√ Save Money
Was way more concerned with the other side and the steering shaft
Torque specs for the bolts?
Tell me, do broken bolts affect the oxygen intake? Can it be that the engine is unstable? If one bolt on each side is broken off?
Yeah, what about that tube like the other guy said attached to the passenger side manifold, that's my problem, all bolts really rusty.
Nice video, i have chevy avalanche 2004 with 5.3liter and don't have that donut. Is it normal?
Yeah, don't show how to get the left side out! The tough one!!!!!
Exhaust manifold bolt torque is a 2 pass. 132 inch pounds then 22 foot pounds
do not… re-use a 2.99 donut gasket…
There was no mention to how to easily remove the dipstick tube. in my experience, you best order a new one before you start this project.
Probably should do this while the engine is warm while being careful.
I need a video on how to remove the exhaust manifold on a 98 Tahoe. it's similar to this, I know, but mine has an air pump which means an extra aluminum tube on the front of the manifold. plus, the second bolt on the front header is busted.
Yes torque specs for header bolts? To skip key info while showing them being torqued is a bit silly.
I would like to see the driver's side done as there are several more obstacles, will the manifold come out without removing any of the steering components? thanks
I'm glad you guys was able to get the dipstick out. I had to just cut mine out of there cuz It wouldn't budge
would installing shorty headers be the same as this
stupid qustion but ar these on both side of engine,
How much did u torque the bolts?
my avalance has a rough idle and check engine light which is throwing a random.misfire code…if done coil packs spark plugs spark plug wires the fuel pressur regulator all 4 oxygen sensors checked fuel pressure it was all In specs checked compression which were.all in specs checked fuel injectors which were all good…still same issue
Quick question, would it be better to do this while the motor is slightly warm, or when it is cold?
I was wondering if I had a broken bolt head or if it was just a support stud thanks for clarifying now I can fix my exhaust leak
Mike, as you mentioned in the video, these gm trucks have the driver's side rear manifold bolt break most of the time. Can you do a video showing how to remove this broken bolt when it is flush on the head? The problem is very common, and is a real pain because it is at the firewall on the driver's side.
Hello Mike ! Is it possible you can make a video for the 01-06 Tahoe exhaust system removal ?